background image

REMOTE ENGINE CONTROL 

 

REMOTE ENGINE STARTING - SUCCESSFUL START DIAGRAM: 

 

REMOTE ENGINE STARTING - UNSUCCESSFUL START 

In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then 
attempts to restart the engine a 2

nd

 and 3

rd

 time.  For hard starting engines, the unit will allow a starter crank 

time of up to10 seconds maximum.  This should provide ample cranking time for difficult starts, but is limited to 
10 seconds to help prevent damage to the starter from over cranking. 
1)  If engine starts on 2

nd

 or 3

rd

 attempt, see steps 4 & 5 (last page) of "Successful Start". 

2)  If Third attempt fails to start engine, the system will turn off and doors will remain locked.  

NO FURTHER 

ATTEMPTS WILL BE MADE AUTOMATICALLY UNLESS YOU PRESS THE START BUTTON AGAIN.

 

 

TURNING OFF A REMOTE STARTED ENGINE: 

1)  Engine is running in Remote Start (Parking lights ON). 
2)  Press and release the Start button for at least 1 second. 
3)  Engine & parking lights turn OFF, Doors remain locked or will re-lock if applicable. 

 

TURNING OFF A REMOTE STARTED ENGINE DIAGRAM: 

 

ENGINE & LIGHTS OFF 

START

 

10 

AFTER

IGN

3

STARTER

THEN

FLASH 1X

SOLID

SOLID

SEC.

START

Summary of Contents for Super Rage CS-2012TW1





















Reviews: