CrimeStopper CS-2205 Installation & Operating Instructions Manual Download

Page: 2 / 32

TABLE OF CONTENTS

Installation Cautions & Warnings…….……………………………………………………………...………………………………..2

Suggested Component Mounting………….…………………………………………………………….……………………….…...3

Wiring (Connectors H1-H8)…………………………………………………………………………………………………………3-12

Power Door Lock Wiring...………………………………………………………………..……………………………………….…4-6

Starter Disable Wiring…………………………..…..…………………………………………………………..………………….10-11

Antenna Diagram………………….……...…………………………………………………………………….…...…………………13

Option Programming……………..………………………………………………………..…………..…….……………………14-18

Programmable Option Reset………………………...……….…………………………………………………….…………….….16

Main System Wiring Diagram………………….…………………………………………………………………………………….19

Remote Programming……..……………………………………………………..………………………....………………………..20

Operation.………………………..…………………………………..….……………….…………………………………….……21-32

2-Vehicle Operation…….…………………………………..….………………………………….…….…………………………….23

INSTALLATION CAUTIONS & WARNINGS

BEFORE BEGINNING

, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS

BRAKES, AND BATTERY).

TO PREVENT A POSSIBLE DEAD BATTERY

remove vehicle dome light fuse while working on the vehicle. MAKE

CERTAIN TO REINSTALL FUSE PRIOR TO TESTING FOR DOOR TRIGGERS.

DO NOT EXCEED MAXIMUM OUTPUT RATINGS! -

SERIOUS DAMAGE MAY OCCUR. LIMITS FOR ALARM FUNCTIONS

ARE LISTED WHERE APPLICABLE.

REMOVE MAIN SYSTEM FUSE (S)

before jump starting the vehicle or charging the battery at high boost. DAMAGE MAY

OCCUR TO SYSTEM IF PROPER PRECAUTIONS ARE NOT OBSERVED.

DO NOT

Mount the control unit or wiring harness in the engine compartment or anywhere they can become entangled with

moving parts such as brake/gas/clutch pedals, or the steering column.

The alarm control module should be mounted in a

concealed location. The antenna wire should be routed away from any metal if possible. Do not alter the length of the
antenna, ground it, or route it with other wires.

Summary of Contents for CS-2205

































Search results

Summary of Contents for CS-2205

Reviews:

Related manuals for CS-2205

Brands by name

Popular brands

CrimeStopper CS-2205, Installation & Operating Instructions Manual

Search results

Summary of Contents for CS-2205

Reviews:

Related manuals for CS-2205

Brands by name

Popular brands