background image

REMOTE CONTROL 

 

4 BUTTON REMOTE TRANSMITTER: 

#3

#1

#2

#4

PANIC

ARM

TRUNK

PANIC

DISARM

(LOCK)

(UNLOCK)

REMOTE

POP

 

 
 

OPERATING INSTRUCTIONS 

 

ACTIVE ARMING 

To arm the alarm and lock the doors, press the #1 (Lock Symbol) button on the transmitter.  You will hear a 
single siren chirp and the lights will flash once. The system will arm, the doors will lock and the starter will be 
disabled if these optional features are installed. The red LED in the vehicle will start flashing after 15 seconds.  
After a short delay to allow vehicle and electronics to stabilize the system will be completely armed. 

 

ALARM TRIGGERING 

If there is an intrusion into the vehicle or hard impact to the body will sound the alarm and flash the lights for 
45 seconds.  After 45 seconds the system will automatically shut off and re-arm to continue to protect the 
vehicle.  If a door is left open, the unit will cycle a second time and still continue to protect the other un-
tampered zones. 

 

DISARMING 

To disarm the alarm and unlock the doors, press the #2 (Unlock Symbol) button on the transmitter.  You will 
hear 2 siren chirps and the lights will flash twice.  The dome light turns on and the dash LED stops flashing. 

 

Summary of Contents for CS-2001.FC.II





















Reviews: