Cretors EG20 Service Manual Download Page 7

  

EG20/32/48/60-M-A/E-S 

Last printed 9/10/2007 1:56:00 PM 

BEGIN SERIAL NO: 00035540 

  

 

D.

 

OEM Option Pedestals 

 

  

1.

 

OEM OPTION machines are designed to supply power to the components 
normally associated with the popcorn machine.  The primary features are a 
power cord with plug and a flexible armored cable to be connected to the 
user’s cornditioner assembly (15 amps).  In addition, a terminal strip inside 
the pedestal provides a connection point to a switch (15 amps) that will 
control a user’s exhaust fan.  Mounting studs for fluorescent ballast and a 
connection point for a light circuit are also supplied.  

  

2.

 

EXHAUST FAN CONTROL machines may be equipped with a time delay 
fan control.  This control provides a timer controlled switch that will turn 
on a customers exhaust fan when the kettle heat is turned on.  When the 
heat is turned off the fan will continue to run for the time set on the timer in 
the pedestal.  This circuit only provides a switch, it does not supply any 
power.  

  

All electrical connections outside the pedestal must be done in accordance 
with appropriate electrical codes and requirements.  

  

E.

 

Pump Installation & Timer Adjustment for Salt/Sugar Machines  

 

  

Refer to the Service Manual included with the pump to be installed in the 
machine.  When the Giant is equipped with the salt/sugar option, also see below 
for additional information.  
  

1.

 

For the Salt/Sugar machine the pump timers are located in the machine 
not in the pump.  One timer is marked “Salt”, the other “Sugar”.  The 
timers are located in the pedestal.  

  

2.

 

To adjust the pump time, use the following procedure:  

  

a.

 

There are two adjustments on the timer.  The small adjustment knob 
sets the maximum time the timer can run.  Cretors will normally set 
this adjustment for 10s.  

  

10s = 0-10 seconds  
1m = 0-1 minute  
10m = 0-10 minutes  
  

b.

 

The larger adjustment knob sets the actual run time (percentage of 
time allowed by the small adjustment knob).  Example:  If the 
maximum setting is set for 10s and the large knob is set at .9, the timer 
will run for 9 seconds.  Adjust to taste for both timers.  

  

 
 

Summary of Contents for EG20




















Reviews: