Cretors EG20 Service Manual Download Page 19

  

EG20/32/48/60-M-A/E-S 

Last printed 9/10/2007 1:56:00 PM 

19 

BEGIN SERIAL NO: 00035540 

  

This manual is filled with time-saving and money-saving information regarding your 
Cretors popcorn popper.  There is nothing, however, more important than the safety 
aids and warnings found throughout this document.  
  
If you have any questions, contact your local distributor and if there are any additional 
questions, feel free to contact the Customer Service Department at C. Cretors and 
Company.  
  
Additional copies of this manual can be obtained from C. Cretors and Company at the 
address listed below.  Please provide model and serial number when requesting 
additional copies of this manual.  There will be a nominal charge for additional copies.  
  
Cretors guarantees this machine to be free of defects in parts, materials and 
workmanship for two years.  Please take this time to fill out the factory registration card 
and return it to the factory to activate your warranty.  If you have any questions 
concerning the Cretors' warranty, please contact your local distributor or the Customer 
Service Department at C. Cretors and Company.  

   

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

   

C. CRETORS AND COMPANY 

 

3243 N. CALIFORNIA AVENUE 

 

CHICAGO, IL 60618 

 

PHONE (773) 588-1690, (800) 228-1885, FAX (773) 588-7141 

 

WEB SITE: 

http://www.cretors.com

  Email: 

[email protected]

  

Summary of Contents for EG20




















Reviews: