CLW-SW, SWS, & SLVS(W/A/B)
CLW-SW, CLW-SWS, & CLS-SLVS Specifications
(continued)
Introduction
SPECIFICATION DETAILS
Load Ratings
3
Incandescent / Tungsten
Halogen
-SW: 1000W
-SWS: 1000W
-SLVS: N/A
Magnetic Low Voltage
4
-SW:
1000VA/750W
-SWS: 1000VA/750W
-SLVS: N/A
Neon / Cold Cathode
4
-SW:
1000VA/750W
-SWS: 1000VA/750W
-SLVS: N/A
Electronic Low Voltage
-SW: 1000W
-SWS: 1000W
-SLVS: N/A
Fluorescent /
High Intensity Discharge
(HID)
-SW: 8A
-SWS: 8A
-SLVS: N/A
General Purpose Fan
-SW: 3.0A
-SWS: 3.0A
-SLVS: N/A
Minimum Load
40W / 0.5A
Operating Temperature
and Humidity
32°F to 104°F (0°C to 40°C )
10 to 90% Relative Humidity
(Non-Condensing)
Dimensions and Weight
-SW and -SWS:
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.91 in (4.85 cm)
Weight: 4.4 oz (0.61 kg)
-SLVS:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.91 in (4.85 cm)
Weight: 3.6 oz (0.50 kg)
Features and Functions
The CLW-SW (-SW) is a stand-alone wall box switch
that can also act as a Cresnet
®
device that reports to a
Crestron
®
control processor. The -SW includes two
isolated, non-polarized Cresnet wires (plus a ground wire)
for connecting to a Cresnet system over a twisted pair
wire with shield.
The CLW-SW features a three-position mode selection
switch. Refer to “Operating Buttons and Switches ” on
page 5 for more information. In the absence of Cresnet
communications, the switch can still be used to control a
load.
The CLW-SWS (-SWS) is similar to the -SW with the
added capability of working with a slave unit
(CLW-SLVS) in a multi-switch / single circuit
application.
The CLW-SLVS (-SLVS) is a slave unit that when used
in conjunction with the -SWS acts as an additional switch
control point in a multi-switch / single circuit application.
It does not connect to a Cresnet system and cannot be
used without a -SWS. The -SLVS does not have a mode
selection switch and is not programmable. It emulates the
operation of the -SWS to which it is connected.
The -SW, -SWS, and -SLVS are available in white,
almond, and black. White units are designated by part
numbers ending in “W”. Almond units are designated by
part numbers ending in “A”. Black units are designated by
part numbers ending in “B”. These switches can be
covered with a decorative faceplate (not supplied).
Specifications
1.
The latest software versions can be obtained from the Crestron
website. Refer to the NOTE following these footnotes.
Following are specifications for the -SW, -SWS, and
-SLVS.
2.
Crestron 2-Series control systems include the AV2 and PRO2.
Consult the latest Crestron Product Catalog for a complete list of
2-Series control systems.
CLW-SW, CLW-SWS, & CLS-SLVS Specifications
SPECIFICATION DETAILS
Power Requirements
Line Power, 120 VAC, 60 Hz
Default Net ID
SW: 6F
SWS: 70
Switch Type
Single-Pole, Single-Throw
Load Type
Incandescent, Tungsten Halogen,
Fluorescent / High Intensity
Discharge (HID), Electronic Low
Voltage, Magnetic Low Voltage, Neon
/ Cold Cathode, General Purpose Fan
2-Series Control System
Update File
1,2
Version 3.093 or later
3.
Refer to Derating Charts for Multigang Installations on page 3.
4.
VA ratings are for input power to the transformer. If you do not
know the input power requirement of the transformer, use the
bulb’s wattage rating to determine proper rating.
NOTE:
Crestron software and any files on the website
are for Authorized Crestron dealers and Crestron
Authorized Independent Programmers (CAIP) only. New
users may be required to register to obtain access to
certain areas of the site (including the FTP site).
Crestron Electronics, Inc.
Installation Guide – DOC. 6134B
15 Volvo Drive Rockleigh, NJ 07647
(2008088)
Tel: 888.CRESTRON
06.05
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
(continued on next column)