background image

Crestron 

C2N-CAMIDSPT

   

Camera Interface, Digital Servo Pan Tilt Head

 

 

Operations Guide - DOC. 6262A 

Camera Interface, Digital Servo Pan Tilt Head: C2N-CAMIDSPT  

  25 

CAMIDSPT General Controls Input and Output Signal Descriptions (continued) 

SIGNAL TYPE 

AND NAME 

DESCRIPTION 

Digital input: 
<

Iris_Local/Auto_Mode

Selects manual or auto mode for controlling the iris. When low 
(default), selects auto mode. When high, selects manual mode.  
High/1 = Manual mode. Low/0 (default) = Auto mode. 

Analog input: <

Preset#

Selects the internal preset to be saved (on the rising edge of 
<

SetPreset

>) or recalled (on the rising edge of 

<

RecallPreset

>). 

Valid values range from 1 to 100. Out of range values are 
disregarded. 

Analog input: 
<

PT_Spd/Time

Specifies either the speed or time, as determined by the 
<

PT_Spd/Time_Adj

> input, for setting the pan/tilt unit to a 

specified position and for recalling presets. 
When in Speed mode, sets the speed for traveling from the 
current pan/tilt position to the target position. The speed ranges 
from 0% (minimum speed) to 100% (maximum speed). 
When in Time mode, sets the time for traveling from the current 
position to the target position. Valid values range from 0.1s to 
25.5s, adjustable in 0.01s increments. 

Analog input: 
<

PT_Acceleration

Sets the acceleration and deceleration for the pan/tilt axes from 
a range of 1% (minimum acceleration) to 100% (maximum 
acceleration). A value of 0% will set the acceleration to a 
default state. 

Analog input: 
<

LensTransTime

Sets the zoom, focus, and iris transition time when the 
ZoomPos, FocusPos, or IrisPos analog input joins are driven. 
This is applicable to servomotor lenses in position mode. 
Valid values range from 0.1s to 25.5s and are adjustable in 
0.01s increments. 

Analog input: <

PanPos

Sets the absolute pan position at the speed or time given by 
the <

PT_Spd/Time

> analog. 

Valid values range from 1 to 65535. A value of 0 will cause no 
movement. A command to a specific position will be processed 
as a preset recall. 

Analog input: <

TiltPos

Sets the absolute tilt position at the speed or time given by the 
<

PT_Spd/Time

> analog. 

Valid values range from 1 to 65535. A value of 0 will cause no 
movement. A command to a specific position will be processed 
as a preset recall. 

Analog input: <

ZoomPos

Sets the absolute zoom position for motorized lenses with 
potentiometer feedback and servomotor lenses in position 
mode. The zoom position is adjusted in the time given by the 
<

LensTransTime

> analog. 

Valid values range from 1 to 65535. A value of 0 will cause no 
movement. A command to a specific position will be processed 
as a preset recall. 

Analog input: 
<

FocusPos

Sets the absolute focus position for motorized lenses with 
potentiometer feedback and servomotor lenses in position 
mode. The focus position is adjusted in the time given by the 
<LensTransTime> analog. 
Valid values range from 1 to 65535. A value of 0 will cause no 
movement. A command to a specific position will be processed 
as a preset recall. 

Analog input: <

IrisPos

Sets the absolute aperture position for servomotor lenses only.  
The aperture is adjusted in the time given by the 
<

LensTransTime

> analog. 

Valid values range from 1 to 65535. A value of 0 will cause no 
movement. A command to a specific position will be processed 
as a preset recall. 

(continued on next page) 

Summary of Contents for C2N-CAMIDSPT









































Reviews: