Camera Interface, Digital Servo Pan Tilt Head
Crestron
C2N-CAMIDSPT
24
•
Camera Interface, Digital Servo Pan Tilt Head: C2N-CAMIDSPT
Operations Guide - DOC. 6262A
CAMIDSPT General Controls Input and Output Signal Descriptions (continued)
SIGNAL TYPE
AND NAME
DESCRIPTION
Digital input:
<
PT_Spd/Time_Adj
>
Selects speed mode or time mode for the pan/tilt absolute
positioning commands (given by the <
Pos
> inputs) and for the
recall preset command.
When low (default), selects Speed mode, where speed ranges
from 0% (minimum speed) to 100% (maximum speed). In this
mode the unit will move from its current position to the target
position at the speed given by the <
PT_Spd/Time
> analog.
When high, selects Time mode, where the time ranges from 0.1s
to 25.5s seconds. In this mode the unit will move from its current
position to the target position in the time given by the
<
PT_Spd/Time
> analog.
High/1 = Time mode; Low/0 (default) = Speed mode.
Digital input: <
Stop
>
Stops pan/tilt and lens movement on the rising edge of the input.
High/1 (rising edge) = Stop movement; Low/0 = No effect.
Digital input:
<
ReportPos
>
Causes the <
Pos_F
> analog outputs to report the current pan,
tilt, zoom, focus, and iris positions, on the rising edge of the
input. On level = high, continuously reports position values that
have changed since last report every 4 seconds
Valid for all modes of operation.
High/1 (rising edge) = Reports all positions immediately;
Low/0 = No effect.
Digital output:
<
ReportPosComplete
>
Pulses high when the position data is valid for the <
ReportPos
>
request. One half-second pulse duration.
High/1 (rising edge) = Data valid;
Low/0 (no pulse) = Data not valid.
Digital input:
<
Iris_Spd/Pos_Mode
>
Selects position or speed mode for controlling the aperture in
servomotor lenses only.
When low, selects position mode, which sets the aperture to the
absolute position given by the <
IrisPos
> analog.
When high, selects speed mode, which will adjust the aperture
at the speed and direction given by the <
IrisRate
> analog.
A change from position to speed mode will send out a stop
voltage. A change from speed to position mode will set the
aperture to <
IrisPos
>.
High/1 = Speed mode; Low/0 (default) = Position mode.
Digital input:
<
Focus_Spd/Pos_Mode
>
Selects position or speed mode for adjusting the focus in
servomotor lenses only.
When low, selects position mode, which sets the focus to the
absolute position given by the <
FocusPos
> analog.
When high, selects speed mode, which adjusts the focus at the
speed and direction given by the <
FocusRate
> analog.
A change from position to speed mode will send out a stop
voltage. A change from speed to position mode will set the focus
to <
FocusPos
>.
High/1 = Speed mode; Low/0 (default) = Position mode.
Digital input:
<
Zoom_Spd/Pos_Mode
>
Selects position or speed mode for adjusting the zoom in
servomotor lenses only.
When low, selects position mode, which sets the zoom to the
absolute position given by the <
ZoomPos
> analog.
When high, selects speed mode, which will adjust the zoom at the
speed and direction given by the <
ZoomRate
> analog.
A change from position to speed mode will send out a stop
voltage. A change from speed to position mode will set the zoom
to <
ZoomPos
>.
High/1 = Speed mode; Low/0 (default) = Position mode.
(continued on next page)
