manualshive.com logo in svg

Cressi NEPTO, Instruction Manual

Share
Download
Cressi NEPTO Instruction Manual Download Page 31

ENGLISH

31

 

   BATTERY REPLACEMENT.

The batter must be replaced whenever the watch display shows the low battery 
symbol.
If the NEPTO shows a steady battery icon, it is able to deliver all functions. Nev-
ertheless, and especially if the watch computer will be used in a cold location, we 
recommend that you replace the battery as soon as possible.

If a flashing battery appears on the display, the dive functions will be disabled for 
safety reasons.

WARNING

:

 

When replacing the battery, all data regarding NO FLY, time, and 

date will be lost. Set the time and date again so the entries in your computer’s 
logbook will be correct. After replacing the battery, all settings return to the 
last value set by the user. The time and date must be reset. To replace the 
battery, use a screwdriver to unscrew the two screws on the cover on the back 
of the device. Remove the cover and inspect the condition of the battery and 
its compartment. If you see any traces of corrosion resulting from leaks, con-
tact an authorized Cressi center to have the device overhauled. If everything 
appears in good condition, remove the battery from its housing by holding 
the computer face down. Replace the battery, checking the correct polarity 
(incorrect polarity may damage the device).
Before closing the cover, check that the compartment is perfectly clean, and 
spread a thin layer of silicone grease on the battery compartment sealing ring.

NOTE

:

 

 Do not over-tighten the battery cover! Over-tightening the cover does 

not create a better seal; on the contrary, it can crack the cover or make it more 
difficult to remove in the future. 

Do not touch or attempt to clean the 

pressure sensor! 

Any malfunctions will be excluded from the warranty.

NOTE

:

 

 Make sure that the instrument is watertight!

WARNING

:

 

 Any malfunctions or water infiltrations due to incorrect battery 

replacement will void the warranty.

LOW BATTERY 

(YOU SHOULD CHANGE THE BATTERY SOON)

YOU MUST CHANGE THE 

BATTERY

(DIVE FUNCTION IS DISABLED)

Summary of Contents for NEPTO





































Reviews:

No comments

Brands by name

Popular brands

Load more brands