Crane SGV2002L Installation And Operation Manual Download

Page: 5 / 38

SECTION: A-1 - PUMP SPECIFICATIONS- SERIES: SGV 2 HP

DISCHARGE:

1-1/4" (32mm) NPT, Vertical

LIQUID TEMPERATURE:

160°F (71°C) Intermittent

VOLUTE:

Cast iron ASTM A-48, Class 30.

MOTOR HOUSING:

Cast iron ASTM A-48, Class 30.

SEAL PLATE:

Cast iron ASTM A-48, Class 30.

IMPELLER:

Design:

10 vane, vortex, with pump out
vanes on back side. Dynamically
Balanced, ISO G6.3.

Material:

85-5-5-5

Bronze

SHREDDING RING:

Hardened 440C stainless steel,
Rockwell C-55.

CUTTER:

Hardened 440C stainless steel,
Rockwell C-55.

SHAFT:

416 stainless steel

SQUARE RINGS:

Buna-N

HARDWARE:

300 series stainless steel

PAINT:

Air dry enamel. Top coat.

SEAL:

Design:

Tandem mechanical, oil filled
reservoir.

Material:

Rotating faces - carbon
Stationary faces - ceramic
Elastomer - Buna-N
Hardware -300 series stainless

CABLE ENTRY:

15ft. (4.5M) cord. Pressure
grommet for sealing and strain
relief.

SPEED:

3450 RPM (nominal).

UPPER BEARING:

Design:

Single row, ball

Lubrication:

Oil

Load:

Radial

INTERMEDIATE BEARING:

Design:

Single row, ball

Lubrication:

Oil

Load:

Radial & thrust

LOWER BEARING:

Design:

Sleeve

Lubrication:

Oil

Load:

Radial

MOTOR:

Design:

NEMA L-single phase,
NEMA B-three
Phase torque curve.
Completely oil-filled,
Squirrel cage induction.

Insulation:

Class

SINGLE PHASE:

Capacitor start/capacitor run. requires overload

protection to be included in control panel. Requires Barnes

starter

or control panel which includes capacitors, or capacitor pack.

THREE PHASE:

Dual voltage 230/460; Requires overload protection

to be included in control panel.

OPTIONAL EQUIPMENT:

Seal material, impeller trims, 12 vane

impeller, moisture sensors (requires relay in panel), additional cable,
CSA listed with SOW-A cables.

WEIGHT:

110 lbs.

inches

(mm)

19.69

(500)

3.87

(98)

11.30

(287)

5.55

(141)

4.63

(118)

9.25

(235)

1-1/4" (32) NPT.

DISCH.

1.13

(29)

Summary of Contents for SGV2002L







































Search results

Summary of Contents for SGV2002L

Reviews:

Related manuals for SGV2002L

Brands by name

Popular brands

Crane SGV2002L, Installation And Operation Manual

Search results

Summary of Contents for SGV2002L

Reviews:

Related manuals for SGV2002L

Brands by name

Popular brands