Crane Barnes EcoTRAN Page 28 Installation & Operation Manual Download | Manualshive

Page: 28 / 35

background image

28

STEP 1: ADAPTER INSTALLATION

A. With the riser attached to the basin, make sure the basin tank assembly is in place and stable in the hole.

The hole should not be completely backfilled.

B. Make sure the riser is cut to the proper length per the hole depth (See STEP 6 on page 12).

C. Install the drain tile o-ring on the top of the riser and lubricate with supplied pipe lube (See STEP 7 on page 13).

D. Push the adapter onto the riser making sure the station power cable and conduit is positioned correctly for wiring

back to the control panel.

E. Install the six retaining fasteners supplied. The fasteners

should fall inside the riser valley per Section View below.

STEP 2: FLOOD PLAIN VENT

(Supplied by Others)

A. When ready to install vent plumbing, remove the 1½” NPT thread protector

B. Plumb as required per Local Codes.

C. Use thread sealant compatible with plastic threads in the adapter vent port

Appendix 4: OPTIONAL FLOOD PLAIN ROCK COVER INSTALLATION

Continued on Page 29

«
...
26
27
28
29
30
...
»

Summary of Contents for Barnes EcoTRAN




































Reviews:

No comments

Related manuals for Barnes EcoTRAN

Brand: Danfoss Pages: 38

Brand: EBARA Pages: 40

Brand: EBARA Pages: 534

Brand: EBARA Pages: 60

Brand: ebm-papst Pages: 8

Brand: Watts Pages: 8

Brand: Oasis Pages: 44

Brand: Gardena Pages: 17

Brand: Gardena Pages: 12

Brand: Navien Pages: 131

Brand: Samoa Pages: 38

Brand: Takagi Pages: 56

224342 A Series

Brand: Graco Pages: 28

AirSite GreenMaster-HP 3-12/12

Brand: Nibe Pages: 104

Brand: Alpha Pages: 15

Brand: Graco Pages: 20

Brand: Zehnder Pumpen Pages: 34

Brand: Nilfisk-Advance Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands