Crane Barnes EcoTRAN Page 24 Installation & Operation Manual Download | Manualshive

Page: 24 / 35

background image

24

Step 20: TIDY-UP & COVER INSTALLATION

• Coil, secure and loop the cords and harnesses to the harness hooks

• Fix any ruts or depressions, which may have occurred during installation.

• Check final grade, (page 19) so it does not interfere with station operation

STANDARD VENTED ROCK COVER INSTALLATION

The cover gasket is a large soft O-ring that is factory installed. Lube the O-ring lightly with the provided lube. Then

install the cover. The rock cover is secured with a twist lock mechanism. Rotate the rock cover clockwise (while

looking at top of cover). Insert lock thru the adapter lock hub and cover lock eye and lock. To remove, unlock rock

cover and turn counter-clockwise.

See APPENDIX 4 for OPTIONAL

Flood Plain Rock Cover Installation.

See APPENDIX 5 for OPTIONAL

Flat Cover Installation.

«
...
22
23
24
25
26
...
»

Summary of Contents for Barnes EcoTRAN




































Reviews:

No comments

Related manuals for Barnes EcoTRAN

Brand: Watson Marlow Pumps Pages: 131

Brand: Eaton Pages: 57

Brand: A.O. Smith Pages: 2

Brand: A.O. Smith Pages: 2

Brand: XPOtool Pages: 10

Brand: Calpeda Pages: 27

Brand: Watts Pages: 12

Brand: Xylem Pages: 92

LOWARA e-SV Series

Brand: Xylem Pages: 48

Optyma Blue OP-LGHE068NTA07D

Brand: Danfoss Pages: 8

Brand: P.I.T. Pages: 20

Brand: Annovi Reverberi Pages: 18

COBRA DS 0600 E

Brand: BUSCH Pages: 24

Infinite Energy2 IW1000

Brand: RBI Pages: 156

Brand: F.F. Group Pages: 28

Brand: OSNA Pages: 40

Brand: Swim & Fun Pages: 136

Brand: Predator Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands