manualshive.com logo in svg

CRANE PUMPS & SYSTEMS BARNES E Series, Installation And Operation Manual

Share
Download
CRANE PUMPS & SYSTEMS BARNES E Series Installation And Operation Manual Download Page 16

SECTION: G REPLACEMENT PARTS

G-1 ORDERING REPLACEMENT PARTS:

When ordering replacement parts, 

ALWAYS

 furnish the

following information:

1. Pump serial number and date code. (Paragraph G-4)
2. Pump model number. (Paragraph G-3)
3. Pump part number. (Paragraph G-2)
4. Part description.
5. Item part number.
6. Quantity required.
7. Shipping instructions.
8. Billing Instructions.

G-2 PART NUMBER:

The part number consists of a six (6) digit number, which
appears in the catalog. A one or two letter suffix may follow
this number to designate the design configuration. This
number is used for ordering and obtaining information.

G-3 MODEL NUMBER:

This designation consists of numbers and letters which
represent the discharge size, series, horsepower, motor
phase and voltage, speed and pump design. This number
is used for ordering and obtaining information.

G-4 SERIAL NUMBER:

The serial number block will consist of a six digit number,
which is specific to each pump and may be preceded by a
alpha character, which indicates the plant location. This
number will also be suffixed with a four digit number, which
indicates the date the unit was built (Date Code). 

EXAMPLE:

 

A012345 0490.

Reference the six digit portion (Serial Number) of this
number when referring to the product.

1

2

3

Typical Name Plate.

16

Summary of Contents for BARNES E Series





























Reviews:

No comments

Brands by name

Popular brands

Load more brands