background image

36

LIMPIEZA Y ALMACENAMIENTO

LIMPIEZA  

Use un cepillo pequeño para limpiar el exterior de la unidad. No 

utilice detergentes fuertes. Los productos de limpieza para el hogar 

que contienen aceites aromáticos como pino y limón, y los 

disolventes como el queroseno, pueden dañar el plástico. Limpie 

todo rastro de humedad con una tela suave.

ALMACENAMIENTO 

•  Nunca almacene la unidad con combustible en lugares donde 

las emanaciones pueden alcanzar llamas abiertas o chispas. 

•  Deje que se enfríe el motor antes de almacenar la unidad. 
•  Trabe la unidad para evitar que se la utilice sin permiso o que se 

provoquen daños. 

•  Almacene la unidad en una zona seca y bien ventilada. 
•  Almacene la unidad lejos del alcance de los niños. 
• Para suspender el accesorio de un gancho, instale la tapa de 

suspensión sobre el accesorio. Asegúrese de que el botón de 

liberación esté firmemente trabado dentro de uno de los orificios 

de la tapa de suspensión. 

Almacenamiento a corto plazo (1-2 semanas) 
1.  Almacene la unidad en posición horizontal. Si esto no es posible, 

almacene la unidad de manera vertical con el motor arriba. 

Almacenamiento a largo plazo 
1.  Retire la tapa de combustible, incline la unidad y drene el 

combustible en un recipiente aprobado. Vuelva a colocar la tapa 

del combustible. 

2.  Arranque el motor y déjelo correr hasta que se detenga. Esto 

asegura que todo el combustible se haya drenado del carburador. 

3.  Deje que el motor se enfríe. Quítele la bujía y eche 5 gotas de 

cualquier aceite de motor de 2 tiempos de alta calidad en el 

cilindro. Jale la cuerda de arranque para distribuir el aceite. 

Coloque nuevamente la bujía. 

4.  Limpie minuciosamente la unidad e inspeccione si hay alguna 

pieza suelta o dañada. Repare o reemplace las piezas dañadas 

y ajuste los tornillos, tuercas o pernos que estén flojos. 

Preparación de la unidad para su uso luego del 

almacenamiento a largo plazo 
1. Retire la bujía de encendido. Incline la unidad para drenar todo 

el aceite del cilindro en un recipiente adecuado. Coloque 

nuevamente la bujía. 

NOTA: No use combustible que haya estado guardado durante más 

de 30 días. Deseche el combustible viejo y aceite de acuerdo 

con las normativas federales, estatales y locales. 

ADVERTENCIA:

 A fin de evitar lesiones personales 

graves, siempre pare el motor y deje que se enfríe antes de 

limpiar o mantener la unidad.

Summary of Contents for CMXGTAMA27SC









































Reviews: