English
8
WARNING:
To reduce the risk of injury, always
remove battery from saw before any of the following
adjustment operations.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start-up can cause injury.
Intended Use
This circular saw is design for do-it-yourself, wood-
cutting applications.
WARNING:
Do not cut any metals, masonry, glass,
tile or plastic with this saw. A dull blade will cause
slow, inefficient cutting overload on the saw motor,
excessive splintering, and could increase the possibility
of kickback.
• DO NOT use any abrasive wheels.
• Use only blades designed for wood cutting.
WARNING:
Cutting sap coated wood, and
other materials may cause melted substances to
accumulate on the blade tips and the body of the saw
blade, increasing the risk of the blade overheating and
binding while cutting.
DO nOT
use under wet conditions or in presence of
flammable liquids or gases.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Attaching and Removing the Blade (Fig. A, B)
1. Retract lower guard and assemble saw blade
6
and
outer blade clamp washer
11
as shown in Figure B.
14
Fig. B
12
6
17
11
2. Depress the spindle lock button
14
while turning the
blade retaining bolt
12
with the hex wrench
17
until
the blade lock engages and the blade stops rotating.
nOTE:
Hex wrench is stored on the saw as shown in
Figure A.
3. Tighten the blade retaining bolt securely with the
hex wrench.
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface.
If wall mounting, locate the charger within reach of
an electrical outlet, and away from a corner or other
obstructions which may impede air flow. Use the back
of the charger as a template for the location of the
mounting screws on the wall. Mount the charger securely
using drywall screws (purchased separately) at least 1”
(25.4 mm) long, with a screw head diameter of 0.28–0.35”
(7–9 mm), screwed into wood to an optimal depth leaving
approximately 7/32” (5.5 mm) of the screw exposed. Align
the slots on the back of the charger with the exposed
screws and fully engage them in the slots.
nOTE:
Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE:
Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™
WARNING:
Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can
be stored on CRAFTSMAN VersaTrack™ Trackwall.
Hooks and accessories are sold separately. Please
refer to the VersaTrack™ Trackwall accessory sheet for
further information.
nOTE:
The CMCB101 charger is not CRAFTSMAN
VersaTrack™ Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 °C – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with
no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
