background image

25

KEY    PART
NO.     NO.              DESCRIPTION

332     690662        Nut (Flywheel)
333     802574        Armature-Magneto
334     691061        Screw (Armature Magneto)
337     802592        Spark Plug
356     692390        Wire-Stop
358     497316        Engine Gasket Set
363     19069          Flywheel Puller
365     692524        Screw (Carburetor)
383     89838          Wrench-Spark Plug
404     690272        Washer (Governor Crank)
425     690670        Screw (Air Cleaner Cover)
443     692523        Screw (Air Cleaner Primer Base)
445     491588        Filter-Air Cleaner Cartridge
455     695161        Cup-Flywheel
456     692299        Plate-Pawl Friction
459     281505        Pawl-Ratchet
505     231082        Nut (Governor Control Lever)
523     495264        Dipstick
524     692296     •  Seal-Dipstick Tube
525     495265        Tube-Dipstick
529     691923        Grommet
562     92613          Bolt (Governor Control Lever)
563     691138        Screw (Debris Guard Cover)
564     690664        Screw (Control Cover)
584     692342        Cover-Breather Passage
585     691879     •  Gasket-Breather Passage
592     690800        Nut (Rewind Starter)
597     691696        Screw (Pawl Friction Plate)
601     95162          Clamp-Hose
604     691757        Cover-Control
608     697671        Starter-Rewind
613     691340        Screw (Muffl er)
615     690340        Retainer-Governor Shaft
616     691308        Crank-Governor
617     270344 •Ø‡Seal-O Ring (Intake Manifold)
621     692310        Switch-Stop
633     691321   ؇Seal-Choke/Throttle Shaft
635     66538          Boot-Sparkplug
668     493823     •  Spacer (Includes 2)
670     692294        Spacer-Fuel Tank

KEY    PART
NO.     NO.              DESCRIPTION

676     393760        Defl ector-Muffl er
677     690661        Screw (Muffl er Defl ector)
684     690345        Screw (Breather Passage Cover)
689     691855        Spring-Friction
703     696309        Clip
718     690959        Pin-Locating
741     691830        Gear-Timing
842     691031     •  Seal-O Ring (Dipstick Tube)
847     692017        Assembly-Dipstick/Tube
851     493880        Terminal-Sparkplug
869     691155        Seat-Valve (Intake)
870     690380        Seat-Valve (Exhaust)
871     262001        Bushing-Guide (Exhaust)
           63709          Bushing-Guide (Intake)
949     696306        Guard-Debris Screen
957     397974        Cap-Fuel Tank
966     496116        Base-Air Cleaner Primer
967     493537        Filter-Pre Cleaner
968     692298        Cover-Air Cleaner
970     691669        Screw (Air Cleaner Primer Bracket)
972     495224        Tank-Fuel
975     493640        Bowl-Float
976     694395        Primer-Carburetor
977     498261        Set-Carburetor Gasket
997     696310        Shield-Debris
1019   494256        Kit-Label
1036   695111        Label-Emission
1058   275177        Owner’s Manual
1059   692311        Kit-Screw/Washer
1210   498144        Assembly-Pulley/Spring (Pulley)
1211   498144        Assembly-Pulley/Spring (Spring)

RPM Adjustments:Low: 1900-2100; High: 3000-3200

•      Included in Engine Gasket Set, Key No. 358
Ø    Included in Carburetor Overhaul Kit, Key No. 121
‡     Included in Carburetor Gasket Set, Key No. 977

NOTE: 

All component dimensions given in U.S. inches

           1 inch = 25.4 mm

MODEL NUMBER 122H02-0220-B1

BRIGGS & STRATTON 4-CYCLE ENGINE

Summary of Contents for 944.361063





























Reviews: