background image

24

MODEL NUMBER 122H02-0220-B1

BRIGGS & STRATTON 4-CYCLE ENGINE

KEY    PART
NO.     NO.              DESCRIPTION

1         697322        Cylinder Assembly
2         399269        Kit-Bushing/Seal
3         299819     •  Seal-Oil (Magneto Side)
4         493279        Sump-Engine
5         691160        Head-Cylinder
7         692249        Gasket-Cylinder Head
8         695250        Breather Assembly
9         696125        Gasket-Breather
10       691125        Screw (Breather Assembly)
11       691781        Tube-Breather
12       692232     •  Gasket-Crankcase
13       690912        Screw (Cylinder Head)
15       691680        Plug-Oil Drain
16       691451        Crankshaft
20       399781     •  Seal-Oil (PTO Side)
22       691092        Screw (Engine Sump)
23       691992        Flywheel
24       222698        Key-Flywheel
25       499429        Piston Assembly (Standard)
           499430        Piston Assembly (.010" Oversize)
           499431        Piston Assembly (.020" Oversize)
           499432        Piston Assembly (.030" Oversize)
26       499425        Ring Set-Piston (Standard)
           499426        Ring Set-Piston (.010" Oversize)
           499427        Ring Set-Piston (.020"Oversize)
           499428        Ring Set-Piston (.030" Oversize)
27       691866        Lock-Piston Pin
28       499423        Pin-Piston
29       499424        Rod-Connecting
32       691664        Screw (Connecting Rod)
32A     695759        Screw (Connecting Rod)
33       262651        Valve-Exhaust
34       262652        Valve-Intake
35       691270        Spring-Valve (Intake)
36       691270        Spring-Valve (Exhaust)
37       694086        Guard-Flywheel
40       692194        Retainer-Valve
43       691997        Slinger-Governor/Oil
45       690548        Tappet-Valve
46       691449        Camshaft

KEY    PART
NO.     NO.              DESCRIPTION

48       498826        Short Block (Replacement 
                              Engine 125H02-0005-D1)
50       497465        Manifold-Intake
51       272199     •  Gasket-Intake
54       691650        Screw (Intake Manifold)
55       697670        Housing-Rewind Starter
58       692259        Rope-Starter (Cut to Length)
60       281434        Grip-Starter Rope
65       690837        Screw (Rewind Starter)
78       691108        Screw (Flywheel Guard)
81       691740        Lock-Muffl er Screw
95       691636        Screw (Throttle Valve)
97       696565        Shaft-Throttle
104     691242     Ø Pin-Float Hinge
117     494870        Jet-Main (Standard)
118     497466        Jet-Main (High Altitude)
121     498260        Kit-Carburetor Overhaul
125     498170        Carburetor
127     694468     Ø Plug-Welch
130     696564        Valve-Throttle 
133     398187        Float-Carburetor
134     398188     Ø Valve-Needle/Seat 
137     693981   ؇Gasket-Float Bowl
146     690979        Key-Timing
159     691753        Bracket-Air Cleaner Primer
163     272653 •Ø‡Gasket-Air Cleaner
187     691050        Line-Fuel (Cut to Required Length)
188     690877        Screw (Control Bracket)
190     690940        Screw (Fuel Tank)
202     691829        Link-Mechanical Governor
209     691291        Spring-Governor
222     692031        Bracket-Control
227     690783        Control Lever-Governor
276     271716   ؇Sealing Washer
287     690940        Screw (Dipstick Tube)
300     692038        Muffl er
304     493294        Housing-Blower
305     691108        Screw (Blower Housing)
306     690450        Shield-Cylinder
307     690345        Screw (Cylinder Shield)

Summary of Contents for 944.361063





























Reviews: