Craftsman 2915 Operator'S Manual Download Page 5

removiNG aND iNstalliNG sliDes

self closiNG sliDes

The self closing feature will pull the drawer closed when 

the drawer is pushed past the slide detent. This is located 

approximatley 1/2" from the fully closed position.

slide removal -

•  The drawers in these units can be rearranged to fit your 

specific needs. This means that drawers may be moved 

or replaced as desired. For example, a 6-inch drawer 

may be replaced by a 2-inch and a 4-inch drawer, or 

three 2-inch drawers.

• First remove the drawer (Refer to Operation A).

•  Lift and hold the spring retainer, and push the slide to-

ward the rear of the unit. The slide may now be removed.

Spring Retainer

slide installation -

•  Place the slide in the appropriate position in the unit and 

pull toward the front of the unit until the spring retainer 

snaps into position and secures the slide.

•  For smooth operation, make sure that the drawers are 

matched with their original slides.

troubleshootiNG

problem

cause

solution

The unit unlocks 

but the drawers 

still will not open.

One or more 

of the drawers 

are holding the 

lockbars from 

releasing.

Completely close 

all the drawers and 

the lockbars will 

release to open the 

drawers.

The cover on the 

chest is holding 

the lockbars from 

releasing.

Apply a downward-

pressure to the 

top of the cover 

to let the lockbars 

release.

The release 

cables are not 

working.

in an UNLOCKEd 

position and pull 

the lock lever sev-

eral times.

The unit is leaning 

too far forward.

Position the unit on 

a level area.

The unit locks but 

some drawers still 

are not locked.

One or more of 

the drawers are 

not compeletly 

closed.

Unlock the unit. 

Close all drawers 

completely. Relock 

unit.

locK system

ball bearing slide

 - Pull slides and slide carrier out to fully 

extended position (see illustration.) Hold the slide on the 

cabinet while aligning it with the slide on drawer. Slightly 

insert one side and repeat for the other side. Slowly push 

drawer to its fully closed position to engage slide. Open 

drawer and reclose to ensure proper operation.

reiNstall DraWers

5

slide carrier

slide

Summary of Contents for 2915













Reviews: