Craftsman Marine CM4.65 Manual Download Page 25 | Manualshive

Page: 25 / 48

background image

25

Crafted with CRAFTSMAN MARINE

8

Maintenance and inspection

Each day, prior to starting the engine, make sure that
the cooling water strainer is not clogged by dirt. Close
the raw water seacock and remove the cover from the
filter housing for proper inspection.
Clean the rubber ring.

Clean the filter element at least twice a year, or
whenever necessary. If the cooling water strainer gets
clogged up, the cooling liquid in the engine may
overheat.

When closing the strainer, make sure that the cover is
perfectly shutting the unit off. If and when air is sucked
into the system, on account of a badly closing filter
cover, there is a severe risk of overheating of the
engine.

Open the raw water seacock, before starting the
engine.

Checking of the cooling water strainer

Cleaning of the cooling water strainer

Check once again!

Make absolutely sure that the cover fits the strainer
housing well and without any air leaks!

«
...
23
24
25
26
27
...
»

Summary of Contents for CM4.65

















































Reviews:

No comments

Related manuals for CM4.65

Brand: Exalto Pages: 28

T-MODE TM 45 R 15/17

Brand: FAAC Pages: 10

Brand: Saito Pages: 2

Brand: Hoval Pages: 12

Brand: Beta Pages: 76

Brand: Texas Equipment Pages: 38

Brand: Texas Equipment Pages: 57

Brand: Texas Equipment Pages: 60

Brand: YS Pages: 2

Brand: Detroit Diesel Pages: 40

Brand: Yanmar Pages: 84

Brand: Uebelhoer Bros Pages: 12

Brand: Mitsubishi Heavy Industries Pages: 111

Brand: Roto Pages: 9

Brand: HPI Racing Pages: 16

Brand: komodo Pages: 12

Brand: M.T.H. Pages: 28

Brand: Hirth Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands