Craftsman Marine CM4.65 Manual Download Page 41

Page: 41 / 48

Crafted with CRAFTSMAN MARINE

Date

Dwg.no.

Revision

Drawn:

Date:

Size:

Checked:

Scale:

Proj.:

Keerweer 33, 3316 KA Dordrecht, The Netherlands. Tel: +31 (0)88 0062600, Fax: +31 (0)88 0062601 - [email protected] - www.craftsmanmarine.com

This drawing is the property of Craftsman Marine B.V., Dordrecht. Copyright reserved acc. law. It is not to be copied (in whole or in part) or other-

wise disclosed without the written consent of Craftsman Marine B.V.

Sheet:

of:

CM4.80 Engine Assembly

Material:

Weight:

Dim. in:

Initials

Description

Product

group:

1:5

A3L

634

984

Exhaust

75 mm (CM4.80)

60 mm (CM4.65)

178

456

95,3

233

585

161

SEA WATER INTAKE

28 mm

MIN 72 - MAX 87 mm

465

379

274

CM4.65/CM4.80 with TMC345

JMZ

06/02/2012

PROPULSION

Overall Dimensions 13

CM4.65 with TM345 Gearbox

Summary of Contents for CM4.65

















































Search results

Summary of Contents for CM4.65

Reviews:

Related manuals for CM4.65

Brands by name

Popular brands

Craftsman Marine CM4.65, Manual

Search results

Summary of Contents for CM4.65

Reviews:

Related manuals for CM4.65

Brands by name

Popular brands