background image

page 7

8. Blade Assembly.

motor housing

blade

blade arm

blade attachment

screws and washers

lock washers 

plastic 

motor lock

WARNING

:  To reduce the risk of serious bodily injury, 

DO NOT use power tools to assemble the blades. If 
screws are overtightened, blades may crack and break.

Time Saver

: Washers for blade screws can be set on 

each blade screw prior to installing blades.

Locate 15 blade attachment screws and washers in 
hardware pack. Hold blade arm up to blade and align 
holes. Insert 3 blade attachment screws (along with 
washers) with fingers first and then tighten screws 
securely with a Phillips screwdriver. Repeat for the 
remaining blades.

Remove blade arm screws and lock washers from 
underside of motor. If plastic motor locks are installed 
with blade arm screws, discard plastic motor locks 
(

save blade arm screws and lock washers to secure blade 

arms

). Align blade arm holes with motor screw holes 

and attach blade arm with lock washers and blade 
arm screws. Before securing screws permanently, 
repeat with remaining blade arms. Securely tighten all 
screws.

NOTE

: Tighten blade arm screws twice a year.

9. Testing Your Fan.

It is recommended that you test fan before finalizing 
installation. Restore power from circuit box and light switch 
(if applicable). Test fan speeds with pull chain. (

diagram 1

Start at the OFF position (no blade movement). First pull 
will set the fan to HI. Second pull will set the fan to 
MEDIUM. Third pull will set the fan to LOW. Fourth pull will 
again set the fan to the OFF setting. If fan does not 
function, please refer to "Troubleshooting" section to solve 
any issues before contacting Customer Service.

 
Turn fan completely off 

before

 moving the reverse switch. 

Set reverse switch to recirculate air depending on the 
season:
 

- DOWN position in summer (

diagram 2

)

 

- UP position in winter (

diagram 3

)

A ceiling fan will allow you to raise your thermostat setting 
in summer and lower your thermostat setting in winter 
without feeling a difference in your comfort.

Important

: Reverse switch must be set either 

completely 

UP

 or 

completely DOWN 

for fan to function. If the reverse 

switch is set in the 

middle

 position (

diagram 4

), fan will 

not operate.

 

Note

: Do NOT remove weatherproof cover from reverse 

switch.

Attach pull chain extension supplied or custom pull chain 
extension (sold separately) to the end of the pull chain.

pull chain

extension

reverse
switch

weatherproof cover

on reverse switch

blade arm screws

Summary of Contents for Porch PF52



















Reviews: