background image

page 7

 7. Wiring.

CAUTION

Be sure outlet box is properly grounded 

and that a ground wire (

GREEN

 or Bare) is present.

Make sure all electrical connections comply with 
Local Codes or Ordinances and the National Electrical 
Code. If you are unfamiliar with electrical wiring or if 
the house/building wires are different colors than 
those referred to in the instructions below, please use 
a qualified electrician.

Note

Excess lead wire length from the fan can be cut 

to the desired length and then stripped.

When fan is secured in place on the hanging 
bracket, electrical wiring can be made as follows:
Connect 

BLACK

 and 

BLUE

 wires from fan to 

BLACK

 wire from ceiling with wire connector 

provided.
Connect 

WHITE

 wire from fan to 

WHITE

 wire from 

ceiling with wire connector provided.
Connect all 

GROUND 

(

GREEN

) wires together 

from fan to 

BARE

/

GREEN

 wire from ceiling with 

wire connector provided.

If you intend to control the fan light with a 
separate light switch connect 

BLUE

 wire from fan  

to the 

BLACK

 (or 

RED) 

supply from the 

independent switch.

* Wrap each wire connector separately with 
electrical tape as an extra safety measure.

This fan is remote control adaptable (remote control 
sold separately).

8. Canopy Assembly.

Temporarily raise canopy to hanging bracket to 
determine which 2 screws in hanging bracket align 
with 

slotted

 holes in canopy, and then lower 

canopy and 

partially loosen

 these 2 screws. 

Remove

 

the 

other

 2 screws and set aside.

Now, lift canopy to hanging bracket again, aligning 
slotted holes in canopy with loosened screws in 
hanging bracket. Twist canopy to lock. Re-insert 
the other 2 screws and secure all screws with 
Phillips screwdriver. 

[

Refer to 

diagram 1

.

Align arrow on canopy ring with the one on the 
canopy. Next, raise the canopy ring over the 
canopy until it is even with the top of the canopy. 
Make sure the canopy and the canopy ring fit 
securely. [

Refer to 

diagram 2

.

]

blue

black

black

white

white

black supply wire

ground

(green

or bare)

white supply wire

*

from ceiling

from fan

ground 
(green or bare)

canopy

canopy

canopy ring

hanging bracket

slotted

hole

diagram 1

diagram 2

Summary of Contents for Helios HE52

























Reviews: