Craftex CX509 User Manual Download Page 2

Page: 2 / 23

TABLE OF CONTENTS

General Safety Instructions .......................................................................... 3

Specific Safety Instructions........................................................................... 4

Features ....................................................................................................... 5

Physical Features ......................................................................................... 6

Unpacking .................................................................................................... 7

Setup ............................................................................................................ 7

Proper Grounding ......................................................................................... 7

Assembly ...................................................................................................... 8

Test Run ....................................................................................................... 9

Adjustments.................................................................................................. 9

Work-piece Inspection ..................................................................................10

Depth of Cut .................................................................................................10

ON/OFF Switch ............................................................................................11

Variable Speed .............................................................................................11

Sanding Belt Replacement ...........................................................................12

Sanding Operation........................................................................................13

Feed Belt Tension and Tracking...................................................................14

Feed Belt Replacement ................................................................................15

V-Belt Replacement & Tensioning................................................................16

Maintenance .................................................................................................17

Cleaning .......................................................................................................17

Lubrication ....................................................................................................17

Parts Diagram...............................................................................................18

Parts List ......................................................................................................19

Warranty .......................................................................................................23

Summary of Contents for CX509
























Search results

Summary of Contents for CX509

Reviews:

Related manuals for CX509

Brands by name

Popular brands

Craftex CX509, User Manual

Search results

Summary of Contents for CX509

Reviews:

Related manuals for CX509

Brands by name

Popular brands