Cover JR 10 User Manual Download | Manualshive

Page: 8 / 19

background image

6

4.

LCD display operation

The PSU is equipped with a color LCD touch panel. Below is a diagram showing the possibilities and
the location of the various information available in the display menu.
For 3: 3 and 3: 1 UPS configurations there are differences in the number of displayed output phases
and bypass phases.
The screens below show a 3: 3 configuration. For a 3: 1 configuration, only 1 Output Phase and Bypass
are displayed.

4.1.

Main display window

«
...
6
7
8
9
10
...
»

Summary of Contents for JR 10




















Reviews:

No comments

Related manuals for JR 10

Brand: Gamatronic Pages: 114

SAFEPOWER S 10KVA

Brand: Siel Pages: 50

Brand: Advantech Pages: 24

Brand: Dale Power Solutions Pages: 36

Brand: Coolmax Pages: 24

Brand: Diablotek Pages: 10

Brand: Tripp Lite Pages: 2

POWERLINE RT-10000

Brand: Ever Power Systems Pages: 63

Proline 3/1 10K

Brand: FSP Technology Pages: 15

Tacoma HT 1K-3KVA

Brand: Maruson Pages: 44

Brand: Eaton Pages: 20

Brand: Eaton Pages: 110

Galleon 1 RT 6K

Brand: ACDC Dynamics Pages: 35

SmartPro Series

Brand: Tripp Lite Pages: 28

Smart Pro SM3000NAFTA

Brand: Tripp Lite Pages: 5

Brand: ICS Pages: 14

Brand: Eaton Pages: 72

Brand: Eaton Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands