Modello - Modèle - Model
Modell - Modelo
BALLET NEXT
Fabbricante - Constructeur
Manufacturer - Hersteller
Fabricante
EPTA S.p.A. - Sede legale
Via Mecenate, 86 - 20138 Milano – Italy
Capitale € 68.515.000 - R.E.A./MI – 1730229
Registro delle Imprese e Cod.Fiscale n. 04160730968
Partita IVA 04160730968
PAGE
20/64
N° DOC
UM000473
14.
PUTTING INTO OPERATION
If the cabinet has been sharply tilted while being sited or for mounting of accessories, it must be left to stand for at
least three hours before being started to allow the lubricating oil to settle in the compressor.
Failure to do so can cause total destruction of the compressor refrigerating system.
Check that the voltage on the identification plate is the same as that of the network.
THE ELECTRICAL SUPPLY LINE TO WHICH THE REFRIGERATOR WILL HAVE
TO BE CONNECTED IS TO BE PROTECTED BY A VERY SENSITIVE
DIFFERENTIAL SWITCH (Rc=16A,Dc=30mA); IT IS ALSO TO BE
LINKED TO THE GENERAL EARTHING PLANT.
Earthing is necessary and compulsory by law.
Absolutely never use reduction units, patch cords, adapters or multiple socket
outlets to connect the counter. DIRECTLY connect the equipment to the mains.
The cable should be fully extended and located where it is unilikely to be struck, caught or stepped on,
away from water and the other liquids and heat sources and must not be damaged. In case of breakage of the power cable of the
cabinet, it must be replaced by the manufacturer or by instruction it change of it.
Follow the manufacturer’s instructions to install the unit, using qualified personnel and complying with the electrical
regulations for the specific country.
Incorrect installation may cause injury and damage; the manufacturer is not liable for this.
The manufacturer disclaims all responsability for any damage to people or things due to
incorrect observance of this rule.
16. OUTER CLEANING
WARNING! TURN OFF POWER SUPPLY TO THE CABINET BY DISCONNECTING THE POWER
PLUG BEFORE CLEANING.
For a good preservation of the cabinet’s body a periodical cleaning is necessary.
1. EXTERNAL BODY:
When necessary, the external body should be cleaned with a cloth and a neutral soap and water solution.
2. STAINLESS STEEL SURFACES:
Wash with warm water and mild detergent, rinse well and dry with soft cloth. Avoid scouring
pads etc. which will spoil the finish of the stainless steel.
3. SURFACES IN PLASTIC MATERIAL:
Wash with warm water and mild detergent, rinse well and dry with soft cloth; under
no circumstances should alcohol, methylated spirits or solvents be used.
4.
GLASS SURFACES:
Only use products specifically designed for glass cleaning; It is not advisable to use ordinary water which
can leave a film of calcium on the surface of the glass.
WARNING!
Do not use jet of water to clean the cabinet: electrical wiring could be damaged.
WARNING!
Never use mechanical devices or any other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
15. MAINTENANCE
WARNING!
Maintenance must be carried out by technical staff trained and enabled for intervention
on the flammable refrigerants.
WARNING! Any work carried out on the appliance by the user strictly requires the power plug being
disconnected from the mains socket.
ATTENTION! Use protective shoes and gloves during maintenance operations.
OPERATION
FREQUENCY
MAINTENANCE
AUTHORISED STAFF
Cleaning the outer surface
Based on use
Ordinary
User
Cleaning the accessible inner parts (do not use tools)
Based on use
Ordinary
User
Seals intactness check
Annuale *
Ordinary
Technical support
Water collection tank cleaning
Annuale *
Ordinary
Technical support
Controllo ed eventuale pulizia del condensatore
Annuale *
Ordinary
Technical support
Sostituzione componenti e parti
-
Extraordinary
Technical support
Any other maintenance operation not planned in the previous points should be carried out by the
support centres authorised by our dealers or by qualified staff.
* Frequenza raccomandata per un funzionamento ottimale del banco e il mantenimento della piena efficienza.
