manualshive.com logo in svg

CORNING AXYGEN I-4010, Instruction Manual

Share
Download
CORNING AXYGEN I-4010 Instruction Manual Download Page 10

8

AXYGEN MICROTUBE SHAKER

 



Complete N number of steps Then, press the knob to start work.

Prog shows the program and step number. Refer to the figure above, 2-2 refers to the total 
number of steps and the current step of the run. 

NOTE: 

Before the Time is set, the step will not take effect. If Time is set to 00:00, it will run in 

continuous mode. Complete the current step input values prior to programming the next step. 

5.3.3 Program with Saving mode

Follow programming practices as mentioned in 5.3.2 for Multiple Step procedures. After the 
program has been built, press and hold, program name characters will flash (refer to the red 
square in below figure). Rotate the knob to organize each program by a P1-P9 naming system. 
Input the preferred P# of the newly generated program and keep for your records, then press 
the knob to complete the input. The program saving is complete now.

Prog shows P1, 5-2, means program number 1 has been selected. P1 was saved with 5 steps 
and currently working through Step 2.

5.3.4 Load Program

While powered On, press and hold the Prog button. This enters the operator into the Load 
program mode. Rotate the knob to show the saved program, from P1 to the last, at most 9 
programs. Switch to the program you want, and press the Prog button to check the program 
details. Then, press the knob to start or run the program. 

5.3.5 Single Function Running 

If Temp is set to ---.-, it means working without temperature control function. When the Time 
is adjusted to 00:00, the product will run in continuous mode. If speed is set to -----, it means 
work without mixing function.

Summary of Contents for AXYGEN I-4010
















Reviews:

No comments

Brands by name

Popular brands

Load more brands