background image

Table of Contents

  1.  Product Description  .............................................................. 1

  2.  Setting the Volume ................................................................ 5

  3.  Aspiration and Dispensing Instructions ........................... 8

 4. Pre-rinsing ................................................................................ 9

  5.  Dense and Viscous Liquids .................................................10

  6.  Axygen® Pipet Tips ...............................................................10

 7. Recommendations ...............................................................10

 8. Recalibration .........................................................................11

 9. Troubleshooting ...................................................................15

 10. Cleaning and Sterilization..................................................17

 11.  Components ..........................................................................18

 12.  Spare  Parts .............................................................................18

 13.  Limited  Warranty .................................................................19

Summary of Contents for Axygen Axypet

























Reviews: