background image

CHD22/CHD30

Dispenser Use

 Page 

11

Basic Model

After the ice machine has operated for a few hours, the CHD dispenser can be used. Pushing 
the ice chute back will activate the dispense mechanism and ice will drop out of the chute into 
the user’s container. 

Coin/Token Model Operation

Without activation the dispenser
will not dispense ice when the ice
chute is depressed.
To activate the dispense system, 
the user must insert a quarter or a 
token in the coin mechanism. If the 
quarter or token is accepted, the 
Ready Light above the ice chute 
glows green, indicating that ice can 
now be dispensed. The dispense 
system will allow ice vending for a 
pre-set time. Once activated, 
pushing the chute in (like the basic
model) causes the ice to vend. At 
the end of the pre-set time, vending 
stops.

Free Vend:

 There is a free vend 

switch inside the unit, switch it to 
ON to bypass the coin mechanism
and vend ice anytime the chute is 
pushed back. 
When switched to Free Vend the 
Ready light will be ON. 
When switching from Free Vend to 
Coin / Token operation the Ready 
light will be ON for a few seconds. 

Summary of Contents for CHD22






















Reviews: