background image

 

Technical Support Manual – 05/2015 Rel. 0                        

Page 3 

To access the "TEST Programs" Menu, proceed as follows (See Figure F2.1): 

1.

 

Enter the SERVICE mode by pressing [F+P3]

  and will be displayed the following messages 

 ; 

2.

 

Press keys [F+P9] 

 

  to access the “TEST Programs” Menu; 

3.

 

Browse the list of the Menus with keys [P4] 

 or [P5] 

  until the option required is displayed. The options 

available are listed in table T2.2; 

Table T2.2: "Parameters" Menu Options 

Options 

Description 

Notes 

ENC 

ENCODER disc reading test 

 

rPM 

Shaft rotation speed test 

 

SiG 

Pick-up signal test  

It also controls the parameters that influence the signal

 

dPy 

Displays and LED test 

 

taS 

Keyboard test 

 

uFC 

Converter voltage-frequency test  

 

Ret 

Return to SERVICE mode 

 

4.

 

Press keys [F+P9]  

 to confirm the option; 

5.

 

5. 

To exit the “TEST Programs” Menu, select the Menu option 

Ret

 and press keys [F+P9]

 

ENC 

 ENCODER disc test 

This menu option allows you to run the ENCODER disc test. When you access this option, the display shows the message 

Enc 000

 

as shown in figures F2.2 and F2.3. 

Figure F2.2: ENCODER disc test message 

 

Figure F2.3: ENCODER disc value message 

 

 

 

Manually turn the wheel and check that values from 000 to 255 (from 000 to 255 turning clockwise and from 255 to 000 turning anti-
clockwise) are displayed. When the reset "tooth" of the encoder disc is in position H12, the value displayed must be 000 (or it must 
be reset to 000 should the value be different). 
If the count is not correct, check and/or adjust the mechanical fixing of the DEB board. Check the cable if there are no mechanical 
problems. 

To exit the ENCODER disc test, press [F+P9]

Summary of Contents for MEC 1




















Reviews: