manualshive.com logo in svg

Coriant 8600, Reference Manual, Page: 6 / 55

Share
Download
Coriant 8600 Reference Manual Download Page 6

Document Information

XFP

10-Gigabit Small Form-Factor Pluggable. A transceiver type used in 8600 ELC1
line card.

Compliance Statement

Hereby, Coriant Oy declares that this product is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC and Directive 2011/65/EU.

FCC Noti

fi

cation Statement

Federal Communications Commission (FCC) Rules require that you be noti

fi

ed of the following:

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modi

fi

cations not expressly approved by Coriant Operations, Inc., in writing can void

the user’s authority to operate the equipment.

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

© 2015 Coriant.

6

Summary of Contents for 8600
























































Reviews:

No comments