manualshive.com logo in svg

Coriant 8600, Reference Manual, Page: 33 / 55

Share
Download
Coriant 8600 Reference Manual Download Page 33

2 Line Unit (LU1)

Pin #

Description

5

Output B-wire (tip)

6

Not connected

7

Not connected

8

Not connected

Pulse per Second and Time of Day Interface Signals of RJ-45, Female 8 Pins

Pin #

Description

1

Pulse per second cable compensation negative,
RS-422 level signal

2

Pulse per second cable compensation positive,
RS-422 level signal

3

Pulse per second negative, RS-422 level signal

4

Ground

5

Ground

6

Pulse per second positive, RS-422 level signal

7

Time of Day negative, RS-422 level signal

8

Time of Day positive, RS-422 level signal

2.3.5

Backplane Data Links

Near End Unit

Remote End Unit

Remote Device

Raw Bandwidth

LU1

SU1

Switch Fabric FPGA

130 Gbp/s with one
operational SU1
200 Gbp/s with two
operational SU1s

LU1

SU1

Control ethernet switch

10 Gbp/s

2.3.6

Power Supply

LU1 contains an integrated power supply (DC/DC converters) on board. It generates all the voltages
needed within different blocks. The input voltage is fed by either of the PIMs (redundancy with
two PIMs). The generated output voltages are galvanically isolated from the battery voltage. LU1
also has polarity protection for input voltages.

2.3.7

Test Features

During boot-up, LU1 performs self tests to verify that the system operational status is nominal.

During normal operation, the CPU monitors the following:

• LU1 operating voltages

• Temperature inside LU1

76.8670-40128B

8600 Smart Routers

© 2015 Coriant.

8665 Smart Router FP7.0 Reference Manual

33

Summary of Contents for 8600
























































Reviews:

No comments