manualshive.com logo in svg

Coriant 8600, Reference Manual, Page: 22 / 55

Share
Download
Coriant 8600 Reference Manual Download Page 22

1 8665 Smart Router Overview

LU1 Features

Feature

LU1 Support

Throughput capacity

130 Gbps/s with one
operational SU1
200 Gbps/s with two
operational SU1s

IPv4 routing

Supported

MPLS switching

Supported

Forwarding

Ethernet MAC switching

Supported

IP VPN

Supported

Services

Pseudowire attachment circuits

Supported

7 DiffServ traf

fi

c classes (EF, AF, BE, CS)

Supported

7 queues per port

Supported

VLAN queuing

Supported

Ingress packet policers

Supported

RED/WRED queue management

Supported

Tail drop queue management

Supported

Strict priority and WFQ scheduling

Supported

Egress port queue shaping

—

Traf

fi

c management

VLAN shaping

Supported

Synchronization

Synchronous Ethernet

Supported

Ethernet Link Protection (ELP)

Supported

[IEEE 802.1AX] Ethernet link aggregation
(intra-IFM) (LAG)

Supported

Equal Cost Multipath (ECMP)

Supported

Fast Reroute (FRR)

—

Virtual Router Redundancy Protocol (VRRP)

Supported

Protection

Ethernet Pseudowire redundancy

Supported

Port and layer 2 protocol statistics

Supported

IP and MPLS statistics

—

Statistics

VLAN statistics

Supported

OAM

[IEEE 802.1ag]/[Y.1731] Ethernet OAM

Supported

L3/L4 access lists

Supported

Miscellaneous

Power consumption measurement

Supported

Control Functionality (CU)

The control functionality (CU) in 8665 Smart Router is run on one or two line units, depending on
the required level of redundancy and the amount of units present in the network element. Note that
the CU on the line units is a completely separate running protected process.

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

© 2015 Coriant.

22

Summary of Contents for 8600
























































Reviews:

No comments