background image

10

Completion

When the camera is installed and set-up as 
required, re-fi t the dome cover to the camera 
base and secure with the three screws using 
the Allen key provided. 

Trouble Shooting

No Picture:
 

- Check the supply voltage to the camera. 

 

- Check the BNC video lead connection. The centre core carries the video signal  

 

   and the outer core or screen is the ‘video signal return’

Picture too bright or dark:
 

- The ALC control is not set correctly

 

- The BLC switch needs setting

Poor Night Time Pictures:
 

- Check the dip switch confi guration, if the camera is supplied with an auto iris    

 

   lens as standard then this should be set for ALC (Auto Iris) and not ELC 

 

   (Electronic Iris).

 

- Check the dip switch confi guration that D/N has been selected.

 

- Check the setup of the camera in its brightest operating conditions and adjust 

 

   the DC level control as described in the instructions.

 

- Select DSS to allow the camera more exposure time.

 

- Check there is suffi cient lighting available for the area being viewed.

Poor Focus:
 

- Check the lens adjustments for focus. 

 

- Check the DC level control. This controls the iris aperture and if it is open too 

 

   much then the picture will not be sharp. 

 

- Check that the dome cover is clean.

 

   To clean the cover, use a soft dry cloth. Do not use caustic or abrasive cleaners 

 

   that may scratch the surface. 

Summary of Contents for 15-CD35F













Reviews: