coov N100 Page 40 Function Instruction Download

Page: 40 / 45

B: connect the "Interface B" of N200T to the HUB K4 through MICRO USB

interface.

：将键盘鼠标格斗摇杆连接至

COOV HUB K4

C: Connect the keyboard and mouse combat rocker to the COOV HUB K4

：将一手柄连上

HUB K4

（此手柄起到按键映射作用）

D: Connect a handle to HUB K4 (this handle serves as a button mapping)

注

：在

X1/PS4

等主机上使用键鼠摇杆，连接

HUB K4

的手柄必须是原装手柄。例

如在

PS4

主机上，此手柄必须是原装

PS4

手柄。在

主机上，此手柄必须是原装

手

柄。在

SWITCH

上，连接

HUB K4

的手柄可以是任意手柄。

Note 1: Use the keyboard and mouse rocker on the X1/PS4 and other hosts, the

handle connected to the HUB K4 must be the original handle. For example, on the

PS4 host, the handle must be the original PS4 handle. On the X1 host, the handle

must be the original X1 handle. On the SWITCH, the handle connected to the HUB

K4 can be an arbitrary handle.

注

：

N200S

不进行任何连接

Note 2: Do not make any connection of N200S.

：

键位映射

. Button mapping

键位映射是将一个按键映射到另一个不同按键上，可实现多个按键相同功能或多个按键

Summary of Contents for N100














































Search results

Summary of Contents for N100

Reviews:

Related manuals for N100

Brands by name

Popular brands

coov N100, Function Instruction

Search results

Summary of Contents for N100

Reviews:

Related manuals for N100

Brands by name

Popular brands