background image

 
 

 

 

Cordless Lawn Mower         

11018                            

Instructions for Use 

 

Please read and retain these instructions for future reference

                                             

v001: 31/10/17 

 

 

WORKING ON BANKS CAN BE DANGEROUS.  

 

DO NOT MOW ON EXCESSIVELY STEEP SLOPES. 

 

ALWAYS BE SURE OF YOUR FOOTING ON SLOPES OR WET GRASS. 

 

MOW ACROSS THE FACE OF SLOPES, NEVER UP AND DOWN. 

 

EXERCISE EXTREME CAUTION WHEN CHANGING DIRECTION ON SLOPES. 

 

USE EXTREME CAUTION WHEN STEPPING BACK OR PULLING THE MACHINE TOWARDS YOU. 

 

NEVER MOW BY PULLING THE MOWER TOWARDS YOU. 

 

STOP THE BLADES IF THE MACHINE HAS TO BE TILTED FOR TRANSPORTATION WHEN CROSSING SURFACES 
OTHER THAN GRASS AND WHEN TRANSPORTING THE MACHINE TO AND FROM THE AREA TO BE MOWED. 

 

SWITCH ON THE MOTOR ACCORDING TO INSTRUCTIONS AND WITH FEET WELL AWAY FROM THE 
BLADE(S). 

 

DO NOT TILT THE MACHINE WHEN STARTING OR SWITCHING ON THE MOTOR, EXCEPT IF THE MACHINE 
HAS TO BE TILTED FOR STARTING IN LONG GRASS. IN THIS CASE, DO NOT TILT IF MORE THAN ABSOLUTELY 
NECESSARY AND TILT ONLY THE PART WHICH IS AWAY FROM THE OPERATOR. ALWAYS ENSURE THAT 
BOTH HANDS ARE IN THE OPERATING POSITION BEFORE RETURNING THE MACHINE TO THE GROUND. 

 

SWITCH ON THE MOTOR ACCORDING TO THE INSTRUCTIONS WITH FEET WELL AWAY FROM ROTATING 
PARTS. 

 

DO NOT PUT HANDS OR FEET NEAR OR UNDER ROTATING PARTS. KEEP CLEAR OF THE DISCHARGE 
OPENING AT ALL TIMES. 

 

ALWAYS STAND CLEAR OF THE DISCHARGE ZONE WHEN OPERATING THE MACHINE. 

 

NEVER PICK UP OR CARRY THE MACHINE WHILE THE MOTOR IS RUNNING. 

 

REMOVE THE SAFETY SWITCH: 

-

 

WHENEVER YOU LEAVE THE MACHINE; 

-

 

BEFORE CLEARING A BLOCKAGE; 

-

 

BEFORE CHECKING, CLEANING OR WORKING ON THE MACHINE; 

-

 

AFTER STRIKING A FOREIGN OBJECT, INSPECT THE MACHINE FOR DAMAGE AND MAKE REPAIRS AS 
NECESSARY; 

-

 

IF THE MACHINE STARTS TO VIBRATE ABNORMALLY (CHECK IMMEDIATELY). 

 

Recommendations for Optimal Handling of the battery 

 

Ensure the switch is in the off position before inserting battery

. Inserting the battery into machines 

that have the switch on invites accidents. 

 

Keep the battery charger away from rain or moisture.

 Penetration of water in the battery charger 

increases the risk of an electric shock. 

 

Recharge only with the charger specified by the manufacturer.

 A charger that is suitable for one type 

of battery may create a risk of fire when used with another battery. 

 

Do not charge other batteries.

 The battery charger is suitable only for charging lithium ion batteries 

within the listed voltage range. Otherwise there is danger of fire and explosion. 

 

Keep the battery charger clean

. Contamination can lead to danger of an electric shock. 

 

Before each use, check the battery charger, cable and plug. If damage is detected, do not use the 
battery charger. Never open the battery charger yourself. Have repairs performed only by a 
qualified technician and only using original spare parts.

 Damaged battery chargers, cables and plugs 

increase the risk of an electric shock. 

 

Do not operate the battery charger on easily inflammable surfaces (e.g., paper, textiles, etc.) or 
surroundings.

 The heating of the battery charger during the charging process can pose a fire hazard. 

 

Use only batteries intended specifically for the machine.

 Use of any other battery may create a risk 

of injury and fire. 

Summary of Contents for 11018














Reviews: