Cooper Sound CS306 Operator'S Manual Download Page 4

1

2

3

5

6

7

8

9

4

24

25

12

13

1

3

4

2

26

27

18

19

16

17

11

10

14

15

22

23

21

20

Meters:

1.

Controls LED brightness.  Use lowest 

setting possible to conserve current 
consumption.

2.  B. TST:

Battery test (see specs)

3.  PK/VU:

The mixer is configured for either VU 
or Peak response meters.
PK:  The reference tone is at -8 dB
VU:  The reference tone is at 0 dB.

4.  OL:

‘Overload’ - Indicates near clip level.  This

LED has a slower release time than the 
others.

 MONITOR 2 

1.  Level:

Monitor 2 gain adjustment

2-5. A,B,C,D

Assigns busses to Monitor 2 output

6-9. Master Faders: 

ABCD - Normally left at maximum for
optimum headroom & signal to noise ratio.

10. Level 

(monitor 1)

:

Gain adjustment

11. PL:

Private line assign to Monitor 1

12. COMM:

Communications return (talkback) to Monitor

1 only (See application note for 2 returns)
The multiturn trimmer above this Switch
adjusts the level.

13. MIC:

Internal slate mic & gain adjustment

14. TAPE/DIR : 

(monitor 1)

Tape or Direct to Monitor 1

15. M/ST/MS : 

(monitor 1)

M = mono, ST = stereo, MS = mid-side

Any combination selected by switches
(16-19) can be monitored in mono, stereo
or mid-side.

16-19. SOLO/OFF/ON

Any combination of busses can be

 A,B,C,D:

monitored.  ‘SOLO’ disconnects the other

busses to the Monitor 1 output - Solo 
mono’s the signal to the headphone out.
‘ON’ - In stereo mode the busses are 
assigned to either (L) left or (R) right.

20. Power:

Internal or external power (center off)

(LED: Turns off at minimum input voltage.)

21,23. Returns:

Trim pots (multiturn) to adjust return (tape)

level to Monitor 1 and the meters

22. TAPE/DIR : 

   (meters)

Tape/Direct: Meters indicate the return 
signals.

OSCILLATOR SECTION

24. OSC:

Internal oscillator:  Up = on, Down = momentary on.

Trimmer (multiturn) above adjusts level

25. Slate:

Slate mic on

26. PL:

Private line to Monitors 1 & 2. The level is 
adjusted by the multiturn trimmer above. (See #11)

27. Roll:

Remote control for many types of recorders (see

separate application note).
Up = Roll; Down = Stop/Pause

2

June 2006

OUTPUT MODULE

MODEL CS306

Summary of Contents for CS306


















Reviews: