manualshive.com logo in svg

Coolmay EX3G-100HA, Programming Manual

Share
Download
Coolmay EX3G-100HA Programming Manual Download Page 41

COOLMAY EX3G PLC/HMI All in one Programming manual

38

RD3A/WR3A interval period

D8126

D8406

D8426

Main version 26232 or higher

version

RD3A\WR3A end operation -1

0

1

2

ADPRW command settings

D8126=0

D8126=1

D8126=2

Main version 26232 or higher

version

ADPRW command settings

D8397=0

D8397=1

D8397=2

Main version 26232 or higher

version

CAN data frame

-

-

M8427

M8196: the activation flag of using programming port protocol and other protocol

(Main version 26232 and

higher, modified to not maintain power failure).

M8125: the activation flag of using MODBUS and the original Mitsubishi function.
M8122: Send flag (this bit needs to be set 1 when using the RS instruction).
M8123: Communication completion flag (communication completion flag when using RS command, needs
to be reset by hand).
M8161: 8-bit/16-bit mode distinguishing flag for RS/RS2 instruction (used in version 26230 and above,
always in 8-bit mode in versions 26210 and 26220)
M8128: Communication completion flag (valid when using RD3A and WR3A for MODBUS
communication, needs to be reset by hand).
M8029: Communication completion flag (communication completion flag when using ADPRW instruction,
needs to be reset by hand).
D8120: Save the communication parameters of the Modbus RTU protocol, and the highest bit of the
communication parameters must be set to E.
D8121: Save the host or slave station number.
D8129: RD3A and WR3A time-out period. (Unit: ms. Better not over 100ms while setting).
D8126: When using the serial port 2 in the ADPRW instruction, set D8126 to 0.

(

Main version

26232 or

lower)
D8126: Interval period. Default as 10 times. (

Main version

26232 or higher.)

D8397:

When using the serial port 2 in the ADPRW instruction, set D8397 to 0.

(

Main version

26232 and

higher version)

Support RS,WR3A,RD3A,ADPRW, Can be set in parameter zone

，

correspond to serial port 2

。

Parameter zone settings are valid only for this channel. Invalid for serial port 3.

2.11.1.1 Mitsubishi programming port protocol

When used as programming port protocol: set M8196=0.

2.11.1.2 Free port protocol

When used as MITSUBISHI protocol: set M8196=1

，

M8125=0

；

the difference between Mitsubishi

protocol 1 and protocol 4 is with end mark OA OD ( stored in D8124, D8125 separately)

2.When used the Mitsubishi protocol, the D8120 only needs to set the lower 8 bits.

Summary of Contents for EX3G-100HA









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands