manualshive.com logo in svg

Coolmay EX3G-100HA, Programming Manual

Share
Download
Coolmay EX3G-100HA Programming Manual Download Page 30

COOLMAY EX3G PLC/HMI All in one Programming manual

27

AD13

R23653

R23673

D8043

R23633

AD14

R23654

R23674

D8044

R23634

AD15

R23655

R23675

D8045

R23635

When 4~20mA,<3.8mA,value is 32760,which is the disconnection value.

2.6.3 Analog input reading 2 (for Main software version 26220)

Thermocouple K (negative temperature), T type, T type (negative temperature) register read values are

shown as below table:

No

K type(negative

temperature)

T type

T type(negative

temperature)

AD0

R23720

R23700

R23740

AD1

R23721

R23701

R23741

AD2

R23722

R23702

R23742

AD3

R23723

R23703

R23743

AD4(Environment

temperature)

R23724

R23704

R23744

AD5

R23725

R23705

R23745

AD6

R23726

R23706

R23746

AD7

R23727

R23707

R23747

AD8

R23728

R23708

R23748

AD9

R23729

R23709

R23749

AD10

R23730

R23710

R23750

AD11

R23731

R23711

R23751

AD12

R23732

R23712

R23752

AD13

R23733

R23713

R23753

AD14

R23734

R23714

R23754

AD15

R23735

R23715

R23755

2.6.4

Analog input reading 3 (for Main software version 26230 and above)

Support FROM instructions or register read directly. Such as: FROM K0 K0 D400 K16 read 16 analog

input, 0~10V.

The register is directly read:

D[8030]~D[8045]

is the output value set for the corresponding type, the

constant scan time is changed to D8059, and it is started by M8039 (version 26232 and above);

NO

Register Value

AD0

D8030

AD1

D8031

AD2

D8032

AD3

D8033

AD4 (environment temp)

D8034

AD5

D8035

AD6

D8036

Summary of Contents for EX3G-100HA









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands