background image

Introduction

The HDBaseT™ 8 by 8 HDMI Matrix over CAT5e/6/7 supports the transmission of 
video (resolutions up to 1080p Full HD and 1920x1200@60Hz), multi-channel 
digital audio and control via IR, RS-232 or Telnet and Web GUI from eight high 
definition sources to eight outputs over a single CAT5e/6/7 cable (up to 100m) for 
each output. It supports high resolution digital audio formats such as LPCM 
7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio as well as 3D
content that can be displayed when connecting a 3DTV and 3D source. Power 
over Ethernet (PoE) support means that compatible receivers do not need their 
own power supplies allowing for greater flexibility in installations and LAN serving 
allows devices such as Smart TVs to be connected to the network.

Features

HDMI, HDCP 1.1 and DVI compliant 

Supports HDMI 3D features

Supports resolutions VGA~WUXGA and 480i~1080p dependent upon the 
output display’s EDID settings

Supports distances up to 100 meters through CAT6/7 cables

Supports 3D signal display dependent upon the output display EDID settings

Supports PoE (Power over Ethernet) on compatible receivers only

Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters at 12-bit
resolution

Supports bi-directional IR from input and output locations

Supports RS-232, remote control, on-panel control and IP Control

Supports LAN serving function through the LAN port

2U size design 

Supports external and internal EDID settings

Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD 
Master Audio transmission

Note:

1. The PoE function is designed for powering compatible receiver units only 

— 

non-PoE receivers will need their own power supply. Receivers of another brand 
may not be compatible.
2. Do not connect the LAN port to CAT outputs of this device or to CAT inputs or 
receiver. Doing so may demage the unit

Applications

Domestic HDMI Matrix System

Video/TV wall display and control

Security surveillance and control

Commercial advertising, display and control

University lecture hall, display and control

Retail sales and demonstration

Summary of Contents for 15204












Reviews: