background image

Safety Rules

Please read these important safety rules

These  safety  alert  symbols  indicate  a  personal  safety  or  property  damage 

instruction exists. ReAD THeSe InSTRUCTIOnS CAReFULLY. 

This  automatic  garage  door  opener  is  designed  and  tested  to  offer  safe 

service provided it is installed and operated in strict accordance with the 

following safety rules. Failure to comply with the following instructions may 

result in death, serious personal injury or property damage.

CAUTIOn:

  If  your  garage  has  no  pedestrian  entrance 

door, an emergency access device should be installed. 

This accessory allows manual operation of the garage door from 
outside in case of power failure.

Position the Garage Door Opener so that the power plug 

is accessible when inserted into the power outlet (EN 

60335-1).

This  opener  should  be  installed  in  accordance  with 

relevant Australian Standards.

Do not allow children to play with door opener controls.

Keep transmitters away from children. 

Watch the moving door and keep people away until the 

door is completely opened or closed.

Activate the opener only when the garage door is in full 

view, free of obstructions and with the opener properly 

adjusted.

Keep  the  garage  door  balanced.  Sticking  or  binding 

doors  must  be  repaired.  Garage  doors,  door  springs, 

brackets  and  their  hardware  are  under  extreme  tension  and 
can cause serious personal injury. Do not attempt any garage 
door adjustment. Do not use if repair or adjustment is needed. 
Call for professional garage door service.

Install the optional wall transmitter in a location where the 

garage door is visible, but out of the reach of children at 

a height of at least 1.5m from the floor. 

Disconnect  electric  power  to  the  garage  door  opener 

before removing covers.

Doors requiring over 400N of force to move must have 

Safety Infra-red Beams fitted.

Do not wear rings, watches or loose clothing while 

installing or servicing a garage door opener.

This opener is not suitable for commercial, industrial 

or common entry applications.

To avoid serious personal injury from entanglement, 

remove all unnecessary ropes or chains and disable 

any equipment such as locks which are not needed for 
powered operation.

Installation and wiring must be in compliance with 

your local building and electrical codes. Connect 

the  power  cord  only  to  properly  earthed  mains.  If  an 
extension lead must be used, make sure it is a 3-core lead 
and approved to 7 amp capacity.

If the power cord is damaged, it must be replaced 

by the manufacturer, its service agent or a similarly 

qualified person in order to avoid a hazard.

When  using  optional  Auto-Close  mode,  a  Safety 

Infra-red Beam (Part No 062734) must be fitted 

correctly and tested at regular intervals. Extreme caution 
is recommended when using Auto-Close mode. All safety 
rules must be followed.

This opener is a plug in domestic appliance and is 

designed for indoor use only. It must be installed in 

a dry position that is protected from the weather. 

The opener is not intended for use by young children 

or infirm persons without supervision.

B&D Doors to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or otherwise which may be implied by laws as 
conditions or warranties of purchase of a B&D Garage Door Opener. B&D Doors hereby further expressly excludes all or any liability for any injury, damage, cost, expense or claim 
whatsoever suffered by any person as a result whether directly or indirectly from failure to install the B&D Garage Door Opener in accordance with these installation instructions.

WARnInG! It is vital for the safety of 

persons to follow all instructions. Save 

these instructions.

Diamond PD 

Power Drive

 : Instruction Manual

© Copyright 2007 B&D Doors

3

Controll-A-Door

®

 P

 

Diamond

 

Instruction Manual

Summary of Contents for P Diamond





































Reviews: