manualshive.com logo in svg

Control Techniques UD77 DeviceNet, User Manual

Share
Download
Control Techniques UD77 DeviceNet User Manual Download Page 41

 

Issue Number:   2 

41 

9.9.4 Revision 

Class:  1 (0x1) 

Instance:  1 (0x1) 

Attribute:  4 (0x4) 

The revision code is the combination of the major and minor revision 
codes, where the major revision code is the low byte, and the minor 
revision code is the high byte. 

Action 

Major Revision 

Minor Revision 

Read 

100

#11.29

 

#11.29 Mod 100 

9.9.5 Status 

Class:  1 (0x1) 

Instance:  1 (0x1) 

Attribute:  5 (0x5) 

This attribute represents the current status of the entire device. Its value 
changes as the state of the  device changes. 

b15 b14 b13 b12  b11 

b10 

b9 

b8 

 

 

 

 Major 

fault (U) 

Major 

fault (R) 

Minor 

fault (U) 

Minor 

fault (R) 

 

b7 b6 b5 b4  B3 

b2 

b1  b0 

 

 

 

 

 Configured  Owned 

R  -  Recoverable fault 

U  -  Unrecoverable fault  

9.9.6 Serial 

Number 

Class:  1 (0x1) 

Instance:  1 (0x1) 

Attribute:  6 (0x6) 

All Control Techniques DeviceNet interfaces have a unique serial 
number stored in the non-volatile memory. 

9.9.7 Product 

Name 

Class:  1 (0x1) 

Instance:  1 (0x1) 

Attribute:  7 (0x7) 

The Unidrive DeviceNet interface will return the string “UD77” when this 
attribute is read. 

Summary of Contents for UD77 DeviceNet

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands