manualshive.com logo in svg

Control Techniques UD52, User Manual

Share
Download
Control Techniques UD52 User Manual Download Page 9

UD52 User Guide
Issue code:  52nu3

5

2.7 Risk 

analysis

In any application where a malfunction of the Drive could lead to damage,
loss of life or injury, a risk analysis must be carried out, and where necessary,
further measures taken to reduce the risk.  This would normally be an
appropriate form of independent safety back-up system using simple
electro-mechanical components.

2.8 Signal 

connections

The control circuits are isolated from the power circuits in the Drive by basic
insulation only, as specified in IEC664–1.  The installer must ensure that the
external control circuits are insulated from human contact by at least one
layer of insulation rated for use at the 

AC

 supply voltage.

If the control circuits are to be connected to other circuits classified as
Safety Extra Low Voltage (SELV) (eg.  to a personal computer), an additional
isolating barrier must be included in order to maintain the SELV
classification.

2.9 Adjusting 

parameters

Some parameters have a profound effect on the operation of the Drive.  
They must not be altered without careful consideration of the impact on
the controlled system.  Measures must be taken to prevent unwanted
changes due to error or tampering.

Summary of Contents for UD52





































Reviews:

No comments

Brands by name

Popular brands

Load more brands