manualshive.com logo in svg

Control Techniques UD52, User Manual

Share
Download
Control Techniques UD52 User Manual Download Page 10

UD52 User Guide

Issue code:  52nu3

6

3 Installing the UD52

Warning

Before using the following procedure, refer to the
Warnings at the beginning of Chapter 2 

Installing the Drive

 in

the Unidrive Installation Guide.

1 

Ensure the Drive is operating in either the Closed-loop Vector or the
Closed-loop Servo mode (this is indicated by parameter 

11.31

 (

0.48

).

2 

Before installing the UD52 in the Unidrive, ensure the 

AC

 supply has

been disconnected from the Drive for at least 10 minutes.

3 

Check that the exterior of the UD52 is not damaged, and that the
multi-way connector is free from dirt and debris.  Do not install a
damaged or dirty UD52 in the Drive.

4 

Remove the terminal cover from the Drive (for removal instructions,
see 

Installing the

 

Drive 

in Chapter 2 of the Unidrive Installation Guide).

5 

Position the multi-way connector on the rear of the UD52 over the
connector in the Drive (see Figure 1), and press on the thumb pad to
push the UD52 into place.

6 

Re-fit the terminal cover to the Drive.

7 

Connect the 

AC

 supply to the Drive.

8 

Set parameter 

.00

 at 

149

 to unlock security.

9 

Check that Menu-16 parameters are now available.

10 

Check that parameter 

16.01

 is set at 

4

.

11 

If the checks in steps 8 and 9 fail, perform the following:

• 

Remove the 

AC

 supply from the Drive.

• 

Wait at least 10 minutes.

• 

Remove the terminal cover.

• 

Check that the UD52 is fully inserted.

• 

Replace the terminal cover.

• 

Re-apply the 

AC

 supply.

• 

Check again that parameter 

16.01

 is set at 

4

.

Summary of Contents for UD52





































Reviews:

No comments

Brands by name

Popular brands

Load more brands