Control Techniques UD52 User Manual Download Page 27

Page: 27 / 36

UD52 User Guide
Issue code: 52nu3

16.14

COS

as reference encoder

0 ~ 1

RW Bit

To use the

SIN

COS

encoder for speed and position reference, set

16.14

at 1.

See

Alternative configurations

in Appendix B

Advanced functions

16.15

COS

encoder– voltage select

0 ~ 1

RW Bit

Caution

A 5V encoder can be damaged if it is supplied with 8V

Use

16.15

to select the encoder

supply voltage from terminal 45,

as follows:

16.15 Voltage

0 +5.15V

+8.0V

16.16

COS

encoder– serial comms.

disable

0 ~ 1

RW Bit

When the initial-position information is not required (or not available) from
the encoder, set

16.16

at 1 to disable the serial communications link. (See

Serial communications

in Chapter 5

Setting Up

)

16.17

COS

encoder– interpolation

disable

0 ~ 1

RW Bit

Set

16.17

1 w

hen the position information is to consist only of the basic

line count (without interpolation being obtained from the intermediate
values of the sine wave outputs of the encoder).

Summary of Contents for UD52





































Search results

Summary of Contents for UD52

Reviews:

Brands by name

Popular brands

Control Techniques UD52, User Manual

Search results

Summary of Contents for UD52

Reviews:

Brands by name

Popular brands