manualshive.com logo in svg

Control Techniques UD52, User Manual

Share
Download
Control Techniques UD52 User Manual Download Page 21

UD52 User Guide
Issue code:  52nu3

17

6 Related Parameters

6.1 Introduction

The parameters listed in this chapter are used for programming and
monitoring the UD52.  Refer to the 

Unidrive User Guide

 for programming

instructions.

Warning

Before attempting to adjust any parameters, refer to the
Warnings and Notes at the beginning of Chapter 3 

Setting up

the Drive

 in the Unidrive User Guide.

6.2 Programmable 

software

Key

Type of parameter

RO Read-only

RW Read–write

...

select 

Select from two settings

...

enable 

Make or allow a function to operate

...

disable 

Stop or disallow a function from operating

...

indicator 

The value can only be read

Limitations of use

S The new parameter-value is saved when the 

AC

 supply is

disconnected from the Drive.

P Protected parameter; the parameter cannot be used as the

destination parameter for a programmable input.

Range

Bi Variable parameter having bipolar value range.

Uni Variable parameter having unipolar value range.

Bit Bit parameter

Symbols

ð

 

Default value

ô

 

Range of values

~ 

Indicates a range of values
(in the case of bit parameters, 

~

 indicates 

or

).

Summary of Contents for UD52





































Reviews:

No comments

Brands by name

Popular brands

Load more brands