background image

11

Package contents

•  C4-Z2IO Zigbee IO
•  Four wall mounting screws
•  Four plastic dry wall anchors
•  Two IR emitters
•  Micro USB power supply

Requirements

•  Composer Pro 2.10.0 or higher

Features

Create a stronger, wider, and more robust Zigbee mesh network than 

ever before using the Zigbee IO. Eliminate any network “dead spots” by 

increasing the reach and density of your Zigbee mesh. Improve Zigbee 

signal latency and provide your customers with higher reliability and 

responsiveness as they use the devices connected to their Zigbee mesh 

network.
The Zigbee IO (Z2IO) is a single device that combines the features of:

•  Remote relays (up to two)
•  Remote contact sensors (up to four)
•  Remote thermistors (two)
•  Internal contact (internal magnetic reed switch)
•  Zigbee-to-IR converters 

Any of these inputs can be used to trigger and control automated 

events—such as sending an e-mail or turning on a cabinet light when its 

door is opened—throughout the Control4 system.
With this device, you can reduce the need to run control wires over long 

distances (or where you can’t run any wires at all).

As Zigbee to IR

The two 3.5 mm IR ports allow you to connect up to two standard IR 

emitters to control any IR-controlled devices, such as TVs, DVRs, and 

receivers. 
When connecting IR emitters, make note of which port each emitter is 

connected to (labeled “1” and “2”). 
IR codes sent from the controller to the Zigbee IO are cached at the 

device, resulting in faster IR control response times.

Micro USB IR 1

IR 2

Note: 

Y IR cables can be used, or IR cables can be spliced 

together (in parallel, not in series), to increase the number 

of controlled devices. Be aware that these connected 

emitters cannot be controlled independently but will all fire 

simultaneously from the shared IR port. Test to verify that 

there is no crossover code functionality between devices 

sharing the same IR port to avoid unwanted side effects.

As a contact and relay

The device has an internal contact along one edge that can be used to 

detect open or closed states when installed with a mounted magnet. Up 

to four contacts (besides the internal contact) or two additional relays, 

or a combination of the two, can be used. Each option is outlined below 

in “Contact and Relay Wiring Options,” and after it’s physically wired, 

the correct option must be set on the 

Properties

 tab as outline further 

below in the section “IO Options.”

As a relay

As a relay, this device provides wireless control of garage door 

openers, window coverings, fireplaces, and pumps (along with other 

relay control applications) inside or outside the home. It integrates 

into Control4 systems as standard relays that can be opened, closed, 

toggled, or pulsed.
The relay enables wireless control of any device controllable by one 

or two low-voltage SPST relays or one simulated SPDT relay. These 

functions appear in a Control4 system as relay outputs (relays) in 

Composer Pro.

SPST

(single pole single throw)

(single pole double throw)

SPDT

(double pole single throw)

DPST

Zigbee IO

Installation Guide

Summary of Contents for Zigbee IO C4-Z2IO








Reviews: