Continental Refrigerator RightViu Mounting Instructions Download Page 39 | Manualshive

Page: 39 / 52

background image

39

NOTE

The assembly and installation of RightViu may only be carried out by trained personnel.

WARNING!

RightViu does not interfere with the vehicle's systems.
RightViu only warns the driver.
RightViu serves only to support the driver, and does not release the driver from his
obligation to drive carefully. The Turn Assist cannot replace looking into your side view
mirrors. It may issue incorrect or false warnings! Drivers must continue to assess their own
driving risks and initiate safe driving manoeuvres whenever necessary.

DANGER!

Changes or manipulation of RightViu can have a negative influence on safety. This may
result in death, severe or minor injuries (personal injury) to the operator or third parties,
property and environmental damages.

Safety instructions

OPERATION

«
...
37
38
39
40
41
...
»

Summary of Contents for RightViu





















































Reviews:

No comments

Related manuals for RightViu

Brand: FMUser Pages: 8

E TRAVELLER VII

Brand: Grundig Pages: 9

Brand: G+M Elektronik Pages: 23

Brand: E.F. Johnson Pages: 69

Brand: perfect pro Pages: 116

Brand: BRIGHT Pages: 69

Brand: H.F.Prints Pages: 8

Brand: Icom Pages: 70

Brand: Gogen Pages: 36

PROFIBUS PA Micropilot FMR53

Brand: Endress+Hauser Pages: 36

Brand: Trevi Pages: 16

Brand: Trevi Pages: 24

Brand: Maas Pages: 16

Brand: Radius Pages: 8

Brand: Hama Pages: 61

Brand: RuarkAudio Pages: 84

Brand: Radio Shack Pages: 24

DAB+ 100 highline

Brand: Kathrein Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands