background image

4

Use and storage  of the 

manual

This assembly manual makes the safe and 

efficient installation and commissioning of 

the RightViu Turn Assist system possible.

The fitter must read through and 

understand this manual before starting 

work. A pre-requisite for safe work is 

compliance with all safety information and 

instructions provided in this manual. In 

addition, the local occupational protection 

regulations and general safety regulations 

for the specific work area apply.

Images in this manual are for general 

understanding and may deviate from the 

actual version used. The operating manual 

makes the safe and efficient use of the 

RightViu Turn Assist system possible. The 

operating manual is part of the product. The 

driver must be provided with the operating 

manual after commissioning. The operating 

manual must be stored in the direct vicinity 

of RightViu and must be accessible to the 

driver at all times. The driver must read 

through this manual and have familiarised 

himself with the system.before driving with 

it for the first time. A pre-requisite for safe 

application is compliance with all the safety 

information and instructions provided in the 

operating manual.

Limitation of liability

Continental shall not be liable for the 

improper installation or use of the Turn 

Assist system or for malfunctions caused by 

the purchaser's other systems.

In particular, Continental shall not be liable 

for assembly or connection errors and for 

damage caused by mechanical influences 

or overvoltage. If not otherwise agreed, 

in particular in individual contractual 

agreements, the following applies to 

Continental’s liability: 

Continental shall be liable for claims for 

damages – for any legal reason – under 

fault-based liability for intentional actions 

and gross negligence.

In case of simple negligence, Continental 

INFORMATION ON THIS MANUAL

Summary of Contents for RightViu





















































Reviews: