Continental Refrigerator RightViu Mounting Instructions Download Page 44

Page: 44 / 52

The following sections describe the maintenance work necessary to ensure

optimal, fault-free operation. The following table lists maintenance work that must

be carried out. The specified intervals must be observed.

WARNING!

Danger of injury due to improper maintenance!
If maintenance work is carried out improperly, this may result in severe injuries and
significant property damage.

INTERVAL

MAINTENANCE WORK

PERSONNEL

Before each trip

Visual inspection

Driver

Check steering angle sensor

Annual

Check alignment

Authorised workshop

As needed

Clean

Driver

NOTE

All maintenance work that may not be

carried out by the driver is described

in the assembly manual, and may

only be completed by an authorised

workshops.

During the general inspection (German MOT), check the alignment of the radar

housing and the position of the steering angle sensor.

Only an authorised workshop may inspect RightViu.

A visual inspection must be carried

out following cleaning of RightViu

NOTE

MAINTENANCE/SERVICING

Summary of Contents for RightViu





















































Search results

Summary of Contents for RightViu

Reviews:

Related manuals for RightViu

Brands by name

Popular brands

Continental Refrigerator RightViu, Mounting Instructions

Search results

Summary of Contents for RightViu

Reviews:

Related manuals for RightViu

Brands by name

Popular brands