Contex SD 3600 series Technical Service Manual Download Page 71

Page: 71 / 85

D-3

Appendix D --- Error codes

System Error:

55-613

Description:

No paper was detected in the scanner.

Corrective Action.

■

Place the correct sheet in the scanner.

Scanner related errors

Error code

100-50122

Keypad

Error code

None

Level

Correctable

Description

pop request failed, position unknown

Potential failed comp.

External, Firmware

Corrective Action.

■

PC (cable, PC hardware/software etc.)

■

Firmware.

Error code

100-50123

Keypad

Error code

None

Level

Correctable

Description

pop request failed, invalid command

Potential failed comp.

External, Firmware

Corrective Action.

■

PC (cable, PC hardware/software etc.)

■

Firmware.

Error code

100-00119

Keypad

Error code

None

Level

Correctable

Description

Invalid SCSI command

Potential failed comp.

External, Firmware

Corrective Action.

■

PC (cable, PC hardware/software etc.)

■

Firmware.

Error code

100-00120

Keypad

Error code

None

Level

Correctable

Description

Invalid value in SCSI CDB

Potential failed comp.

External, Firmware

Corrective Action.

■

PC (cable, PC hardware/software etc.)

■

Firmware.

Error code

100-00121

Keypad

Error code

None

Level

Correctable

Description

Invalid SCSI parameter list length

Potential failed comp.

External, Firmware

Corrective Action.

■

PC (cable, PC hardware/software etc.)

■

Firmware.

Error code

100-00123

Keypad

Error code

None

Level

Correctable

Description

Unsupported SCSI parameter

Potential failed comp.

External, Firmware

Corrective Action.

■

PC (cable, PC hardware/software etc.)

■

Firmware.

Error code

100-00124

Keypad

Error code

None

Level

Correctable

Description

Invalid SCSI parameter value

Potential failed comp.

External, Firmware

Corrective Action.

■

PC (cable, PC hardware/software etc.)

■

Firmware.

Error code

100-00125

Keypad

Error code

None

Level

User

Correctable

Description

Incorrect scanner status. Please check the paper path and

reload

the

media.

Potential failed comp.

External, Firmware

Corrective Action.

■

PC (cable, PC hardware/software etc.)

■

Firmware.

Summary of Contents for SD 3600 series






















































































Search results

Summary of Contents for SD 3600 series

Reviews:

Related manuals for SD 3600 series

Brands by name

Popular brands

Contex SD 3600 series, Technical Service Manual

Search results

Summary of Contents for SD 3600 series

Reviews:

Related manuals for SD 3600 series

Brands by name

Popular brands